I'm after a flywheel puller for my NC23, can anyone confirm the thread size for me? I've seen one with an M14 x 1.5 thread but I'm not sure this will fit.
If anyone can help or point me in the right direction I'd be very grateful!!
Cheers,
Matt
Flywheel Puller
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
Matt
- Settled in member
- Posts: 34
- Joined: Tue Sep 23, 2008 9:34 pm
Flywheel Puller
Hi all,
I'm after a flywheel puller for my NC23, can anyone confirm the thread size for me? I've seen one with an M14 x 1.5 thread but I'm not sure this will fit.
If anyone can help or point me in the right direction I'd be very grateful!!
Cheers,
Matt
I'm after a flywheel puller for my NC23, can anyone confirm the thread size for me? I've seen one with an M14 x 1.5 thread but I'm not sure this will fit.
If anyone can help or point me in the right direction I'd be very grateful!!
Cheers,
Matt
-
clemsta
- Settled in member
- Posts: 7
- Joined: Fri Jan 16, 2009 8:24 pm
Re: Flywheel Puller
did you get a flywheel puller, i might be needing one soon, what did you find out?
Adam
Adam
-
wullvfr
- Site Supporter
- Posts: 1027
- Joined: Wed Apr 30, 2008 8:40 pm
- Bike owned: zx9r c1
- Location: killin,scotland
Re: Flywheel Puller
hello-
i can't confirm it is the correct size for the nc23 but i think it is the same size as the one i have for the nc30!!!!
and they will more than likely be the same.
contact graeme france who is a member on here,they will stock the flywheel/rotor puller
william
i can't confirm it is the correct size for the nc23 but i think it is the same size as the one i have for the nc30!!!!
and they will more than likely be the same.
contact graeme france who is a member on here,they will stock the flywheel/rotor puller
william
please,god,....give me the chance to prove that winning the lottery won't spoil me!!!
-
Matt
- Settled in member
- Posts: 34
- Joined: Tue Sep 23, 2008 9:34 pm
Re: Flywheel Puller
Hi guys,
After diong some research and hunting high and low for a puller that fits (after refusing to pay Mr. Hondas prices) i managed to find a bolt that would do the job. The thread is M16 x 1.5, which isn't the same as the NC30.
This link is to a website that i found, scroll down to the 'Hex fine Rotorvator bolts' and there she is, M16 x 1.5 in a selection of legnths in stock standard part. I paid less than £3 delivered, and it done the job lovely! Probably the most important bolt I've ever bought!
http://www.beeversales.com/products10.html
Just use a rubber strap wrench to hold the flywheel in the opposite direction, and wind the bolt in, might need a gentle persuation with a rubber mallet but mine just popped off!
Hope that helps.
Cheers, Matt
After diong some research and hunting high and low for a puller that fits (after refusing to pay Mr. Hondas prices) i managed to find a bolt that would do the job. The thread is M16 x 1.5, which isn't the same as the NC30.
This link is to a website that i found, scroll down to the 'Hex fine Rotorvator bolts' and there she is, M16 x 1.5 in a selection of legnths in stock standard part. I paid less than £3 delivered, and it done the job lovely! Probably the most important bolt I've ever bought!
http://www.beeversales.com/products10.html
Just use a rubber strap wrench to hold the flywheel in the opposite direction, and wind the bolt in, might need a gentle persuation with a rubber mallet but mine just popped off!
Hope that helps.
Cheers, Matt