What did you do with your NC30/35 today?

Post by **crookzy1** » Sun Aug 23, 2015 9:58 pm

VtypeV4 wrote:Hope you get it sorted, Pete.

Thrashed mine up through Beech / A519, down to the Darlaston / A51 then back up and over to the A53 before heading home and narrowly avoiding the rain.

Unfortunately I didn't avoid the rain...tour of Essex B roads featuring knee-deep flooding in some areas. Still had some fun

Post by **fatpete** » Wed Aug 26, 2015 4:54 pm

Well I am up and running again. Ran all the test on the charging system, all seemed fine apart from low charging voltage at the battery 12.5v @5k. Alternator is gsxr and tests showed ok, battery is good, swapped the Reg/rec and straight up to 14.6v @5k. So a bit of a strange one but all seems to be working!

Still the breakdown got me out of going to the in-laws so not all bad!

Post by **micpec** » Wed Aug 26, 2015 5:01 pm

Cleaned one plug (air blasted) after i started the nc35 standing still since last year trip to the Alps, and filled up the tank with fresh fuel just across border (few miles away from Belgium) where the fuel price is silly low) and had nice ride in the area.

Post by **greggo** » Thu Aug 27, 2015 11:54 am

For a start, I just bought one. NC35 race bike. Has pressurised airbox among other things.

Needs some serious tlc after being neglected for several years. She'll get a strip down and rebuild with new mains and rings at the very least. Anything else as needed.

Post by **greggo** » Thu Aug 27, 2015 11:57 am

Was quite a well known bike here. And is my return to 400s and this forum after a 4 or 5 year absence.

Post by **micpec** » Thu Sep 03, 2015 10:30 pm

Did some carb work today in my workshop. Ultrasonic cleaned all three sets fully, fitted one set on the project bike and within few seconds she came alive in just couple of seconds, and that after three years under the cloth...naked no panels nothing.

vfrman · Post by **vfrman** » Sat Sep 05, 2015 6:02 pm

Another track day. She is starting to really puff smoke on the decel. One more race weekend and it will be time to take a serious look at the top end.

ImageUploadedByTapatalk1441472540.520414.jpg

Post by **tillett22** » Tue Sep 08, 2015 10:07 am

Started to build my newly painted master cylinder

Post by **marcus57** » Thu Sep 10, 2015 9:50 pm

vfrman wrote:Another track day. She is starting to really puff smoke on the decel. One more race weekend and it will be time to take a serious look at the top end.
ImageUploadedByTapatalk1441472540.520414.jpg

Are they nc specific stomp grips or did you cut them yourself?

vfrman · Post by **vfrman** » Thu Sep 10, 2015 10:34 pm

marcus57 wrote:
vfrman wrote:Another track day. She is starting to really puff smoke on the decel. One more race weekend and it will be time to take a serious look at the top end.
ImageUploadedByTapatalk1441472540.520414.jpg
Are they nc specific stomp grips or did you cut them yourself?

I sent techspec a template to cut me some grips. I'm sure they still have it. Tell them I sent you. :)

What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?

Re: What did you do with your NC30/35 today?