Yoke, Clipons, Lever perches and other colours?
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
- Familiar Member
- Posts: 290
- Joined: Tue Feb 05, 2013 5:52 pm
- Location: South Africa
Yoke, Clipons, Lever perches and other colours?
Hi, I found another thread where it said that "Yoke and lever perches satin black.clipons gloss black." but what about the actual handle bars (they look gloss black to me?) and the metal throttle cable housing (toss up between satin black and gloss black?) then what colour should the brake fluid reservoir bracket be (in my opinion gloss black against the satin black will look good?) lastly what colour is the key / lock cap (ie the surround around the key that says on off etc) - again I think gloss black as a contrast against the satin black will look good... all these bits are going to the powdercoaters on tuesday so hopefully someone has some info for me before it goes otherwise thats whats going to happen 

- VFRkieran
- Site Supporter
- Posts: 839
- Joined: Fri May 06, 2011 8:37 pm
- Bike owned: NC30, NSR250, CBR600, TS125
- Location: Oxfordshire
Re: Yoke, Clipons, Lever perches and other colours?
Pretty sure the handle bars are gloss black too, metal throttle cable housing (if im thinking of the correct thing) should be zinc coated in the olive green colour thats a nightmare to match properly, same with the M/C bracket but ive just painted that satin.
-
- Familiar Member
- Posts: 290
- Joined: Tue Feb 05, 2013 5:52 pm
- Location: South Africa
Re: Yoke, Clipons, Lever perches and other colours?
Thanks, it all prepped for the powdercoating shop tomorrow ... quite a mission... amazing how many holes need to be filled with an old bolt to make sure the powercoating doesnt clog the threads (also quite a story to strip and blank off the master cylinder on the brake lever)... anyway... its going to be pretty when its done
.

-
- Familiar Member
- Posts: 290
- Joined: Tue Feb 05, 2013 5:52 pm
- Location: South Africa
Re: Yoke, Clipons, Lever perches and other colours?
Next colour question... dont know what the part is called but the metal section that sits inside the sprocket (the sprocket fastens to it and it fastens to the rear wheel)... its black but mine is faded - what colour black is it supposed to be? Thanks
-
- Site Supporter
- Posts: 1292
- Joined: Thu Nov 20, 2008 1:09 pm
-
- Familiar Member
- Posts: 290
- Joined: Tue Feb 05, 2013 5:52 pm
- Location: South Africa
Re: Yoke, Clipons, Lever perches and other colours?
Thanks man - I was feelin a little ignored 

- Drunkn Munky
- Site Supporter
- Posts: 6313
- Joined: Thu May 01, 2008 9:37 am
- Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
- Location: Kent
Re: Yoke, Clipons, Lever perches and other colours?
I wouldn't powdercoat the clip on bars, the throttle tube wont go back over.
-
- Familiar Member
- Posts: 290
- Joined: Tue Feb 05, 2013 5:52 pm
- Location: South Africa
Re: Yoke, Clipons, Lever perches and other colours?
Thanks Dave, I have taped up the bars, will be spray / can painting that bit
-
- Familiar Member
- Posts: 290
- Joined: Tue Feb 05, 2013 5:52 pm
- Location: South Africa
Re: Yoke, Clipons, Lever perches and other colours?
My bike is a 92 - black calipers... But what black? I am guessing they should be satin black (with white nissin lettering?) - does anyone know? Thanks