Matching Models with NC29?
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
Crazy_German
- Settled in member
- Posts: 54
- Joined: Thu Mar 24, 2011 11:18 pm
- Bike owned: CBR 400 RR NC29
- Contact:
Matching Models with NC29?
Hey everybody.
Does anybody know which Honda models share same parts with the NC29? I´m looking for some special levers from Pazzoracing but they don´t have the NC29 listet.
But I found out for example that the CBR 900 SC33 have the same rearsets as the NC29. I´ve just seen pictures of the rearsets but the look exactly the same.
The big automobile manufactors do it the same way and use as same many parts as possible in different models so maybe Honda has done it with their Bikes too!?
Can anybody help out? Just need to know about the rearsets and about the levers. I know there are aftermarket Levers and Rearsets for the NC29 but I just wan´t that other ones!
Does anybody know which Honda models share same parts with the NC29? I´m looking for some special levers from Pazzoracing but they don´t have the NC29 listet.
But I found out for example that the CBR 900 SC33 have the same rearsets as the NC29. I´ve just seen pictures of the rearsets but the look exactly the same.
The big automobile manufactors do it the same way and use as same many parts as possible in different models so maybe Honda has done it with their Bikes too!?
Can anybody help out? Just need to know about the rearsets and about the levers. I know there are aftermarket Levers and Rearsets for the NC29 but I just wan´t that other ones!
-
garyboy_palaboy
- Familiar Member
- Posts: 267
- Joined: Sun May 04, 2008 9:43 am
Re: Matching Models with NC29?
for levers, there are some aftermarkets that are specifically for NC29 but most are "generic" levers, or copycats. if you want some good clutch levers, just pick any good levers like titax, rizoma, etc. from any bike models and make sure to buy the same bikes clutch perch. clutch perch are not that expesive.
for brake levers, since youre planning to buy expensive disk brakes why not buying a brembo brake master? there are tons of good brembo brake levers around.
for the rearset, the fastest way is to pick the shortest adjustable rearsets and make a template.
for brake levers, since youre planning to buy expensive disk brakes why not buying a brembo brake master? there are tons of good brembo brake levers around.
for the rearset, the fastest way is to pick the shortest adjustable rearsets and make a template.
-
Cammo
- Site Supporter
- Posts: 4505
- Joined: Thu May 01, 2008 12:35 am
- Bike owned: NC30
- Location: Melbourne, Australia
Re: Matching Models with NC29?
CBR600 F4i levers will fit.
Nearly all honda sports bikes that use non-radial master cylinders use the same levers.
Nearly all honda sports bikes that use non-radial master cylinders use the same levers.
"It's just a ride" Bill Hicks
-
garyboy_palaboy
- Familiar Member
- Posts: 267
- Joined: Sun May 04, 2008 9:43 am
Re: Matching Models with NC29?
i remember this once mentioned here.Cammo wrote:CBR600 F4i levers will fit.
i got question guys.... do you think that the triple tree assembly of NC35 will fit on NC29, especially on the forks?
.
-
tanuki
- Site Supporter
- Posts: 1571
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
Re: Matching Models with NC29?
the only way they are a direct fit is to leave one of the stem locking nuts off, if you are not happy doing this (as I was not) you will need to have the RVF stem replaced with the CBR one.
-
amorti
- Regular Member
- Posts: 957
- Joined: Sun May 18, 2008 4:51 pm
- Bike owned: CB-1, MSX125
- Location: Gibraltar
Re: Matching Models with NC29?
If that's how close it is, couldn't you have a small amount milled off the bottom of the top yoke in the corresponding area?tanuki wrote:the only way they are a direct fit is to leave one of the stem locking nuts off, if you are not happy doing this (as I was not) you will need to have the RVF stem replaced with the CBR one.
-
Crazy_German
- Settled in member
- Posts: 54
- Joined: Thu Mar 24, 2011 11:18 pm
- Bike owned: CBR 400 RR NC29
- Contact:
Re: Matching Models with NC29?
Hey thanks Cammo for the advice.
I guess I found an other Honda model with the same rearsets: the CBR 900 SC33. If you google "CBR 900 SC33 rearsets" you find pictures of the same rearsets as the NC29 got.
The technical service from Gilles.Tooling said that they won´t fit cause the dimension from the screws that hold the rearsets on the frame would be 1 mm to short, but thank could be an measurement failure of mine.
I´ve just send them a test sheet with all measurements of the NC29 rearsets and it´s easy to make an failure of 1 mm when measure center hole distance.
So i´m going to order one of that SC33 rearsets and when they fit i´ll let you know guys.
I guess I found an other Honda model with the same rearsets: the CBR 900 SC33. If you google "CBR 900 SC33 rearsets" you find pictures of the same rearsets as the NC29 got.
The technical service from Gilles.Tooling said that they won´t fit cause the dimension from the screws that hold the rearsets on the frame would be 1 mm to short, but thank could be an measurement failure of mine.
I´ve just send them a test sheet with all measurements of the NC29 rearsets and it´s easy to make an failure of 1 mm when measure center hole distance.
So i´m going to order one of that SC33 rearsets and when they fit i´ll let you know guys.