Useful NC30/35 info

[royster81]

wheel bearings are 6004 2RS

[CMSMJ1]

Good idea!

Front axle bolt - 24mm

Yeah..one of my bikes has a 22mm and the other a 24mm..so there!

[royster81]

i think the rvf is a 22mm bolt.

[spongy.bob]

hopefully these are handy....


"M" Length (mm) Tread (turns per mm) Gap between base of head and start of threat. (un-threaded shaft) head type Quantity
RHS of Bike engine case 6 40 1 20 Cap/cheese head H5 alan key 2
6 32 1 12 Cap head H5 10
Clutch Cover 6 28 1 8 Cap head H5 4
6 25 1 5 Cap head H5 1
Water Pump 6 35 1 15 Cap head H5 1
6 25 1 5 Cap head H5 1
6 32 1 12 Cap head H5 1
6 65 1 45 Cap head H5 1
6 10 1 0 Cap head H5 1
Sproket Cover 6 32 1 12 Cap head H5 1
6 70 1 50 Cap head H5 1
6 80 1 60 Cap head H5 1
6 110 1 90 Cap head H5 1
Drive cover 6 12 1 0 Cap head H5 2
Reservior bolts 4 45 1.5 0 Counter sunk H5 2
Bar end bolts 6 55 1 0 Counter sunk H5 2

[spongy.bob]

ok that didn't come out very well! I'll re-format and re-post.

[spongy.bob]

RHS of Bike engine case:
M6, length 40mm, thread (turns per mm) 1, un-threaded shaft (from base of head too thread) 20mm, quantity x2.
M6, length 32mm, thread 1, un-threaded shaft 12mm, quantity x10.

Clutch Cover:
M6, length 28mm, thread 1, un-threaded shaft 8mm, quantity x4.
M6, length 25mm, thread 1, un-threaded shaft 5mm, quantity x1.

Water Pump:
M6, length 35mm, thread 1, un-threaded shaft 15mm, quantity x1.
M6, length 25mm, thread 1, un-threaded shaft 5mm, quantity x1.
M6, length 32mm, thread 1, un-threaded shaft 12mm, quantity x1.
M6, length 65mm, thread 1, un-threaded shaft 45mm, quantity x1.
M6, length 10mm, thread 1, unthreaded shaft 0mm, quantity x1.

Sprocket cover:
M6, length 32mm, thread 1, un-threaded shaft 12mm, quantity x1
M6, length 70mm, thread 1, un-threaded shaft 50mm, quantity x1.
M6, length 80mm, thread 1, un-threaded shaft 60mm, quantity x1.
M6, length 110mm, thread 1, un-threaded shaft 90mm, quantity x1.

Drive Cover:
M6, length 12mm, thread 1, un-threaded shaft 0mm, quantity x2.

Reservoir Bolts:
M4, length 45, thread 1.5 turns per mm, un-threaded shaft 0mm, quantity x2.

[spongy.bob]

That's better!

Up yours Pro Bolt!

[silentRVF]

Good idea!

Front axle bolt - 24mm

Yeah..one of my bikes has a 22mm and the other a 24mm..so there!

My RVF is 22mm as well :)

[Hadies]

NC30
Top yoke pinch bolts - M7 x 50mm Socket cap
Fork pinch bolts - M8 x 45mm Flanged hex
Ignition Barrel - M8 x 20mm Torx head