The Exhaust Thread

Post by **ibby4585** » Fri Feb 04, 2011 7:45 pm

royster81 wrote:Too many people for me now, I think I'm going to take mine off for an ethos

I got a full one of them too!!

Post by **Drunkn Munky** » Fri Feb 04, 2011 8:09 pm

royster81 wrote:Too many people for me now, I think I'm going to take mine off for an ethos

Yeah common as muck, think i'll find a BEET TI system for it next

vfrman · Post by **vfrman** » Sat Feb 05, 2011 6:09 am

Drunkn Munky wrote:
royster81 wrote:Too many people for me now, I think I'm going to take mine off for an ethos
Yeah common as muck, think i'll find a BEET TI system for it next

I didn't know BEET made a TI system!

Post by **ibby4585** » Sat Feb 05, 2011 8:14 am

vfrman wrote:
Drunkn Munky wrote:
royster81 wrote:Too many people for me now, I think I'm going to take mine off for an ethos
Yeah common as muck, think i'll find a BEET TI system for it next

I didn't know BEET made a TI system!

Super duper rare! But they did make a few!!

Kris

ludacris · Post by **ludacris** » Sat Feb 05, 2011 3:36 pm

hey what's the best and cheapest way to get a TSR system under 94dB? need to get RWC soon (MOT) and no doubt the system is over 100dB and I dont want to fork out the stupid prices they charge here for the stock system on something I'd only need for an hour or two..

Post by **Drunkn Munky** » Sat Feb 05, 2011 4:57 pm

ludacris wrote:hey what's the best and cheapest way to get a TSR system under 94dB? need to get RWC soon (MOT) and no doubt the system is over 100dB and I dont want to fork out the stupid prices they charge here for the stock system on something I'd only need for an hour or two..

Baffle?? or if you dont wanna drill a hole for the baffle borrow a can for the MOT.

ludacris · Post by **ludacris** » Sat Feb 05, 2011 11:38 pm

unfortunately removable baffles will fail you so it would have to be welded in which is out of the question lol, so it needs to be something that's hidden...i would struggle to borrow a stock one where I am..

Post by **uber pikey** » Sat Feb 05, 2011 11:41 pm

You can always tack weld one in, then dremmel it out afterwards

Post by **Drunkn Munky** » Sun Feb 06, 2011 12:14 am

Are removable baffles not an option in OZ then?

If you really must have something thats hidden just for the MOT then take the can off and stuff something up the inlet side and make sure it wont come out, piece of tin with a few holes in might work. Ive seen people shove coke cans in the their pipes at trackdays to get through noise testing.

ludacris · Post by **ludacris** » Sun Feb 06, 2011 2:41 am

from what I remember last time I looked into baffles they were illegal if they are removable...essentially it's seen as you will remove it as soon as the test is completed so it's either no baffle or permanently affixed...no moddle area

read that steel wool is an option through the intake side but kinda concerned about creating back pressure if there's not enough holes for the air to pass through and don't want to fudge things up..

would something like this work through the inlet side?: http://cgi.ebay.com.au/stainless-race-b ... 45f8776a55

The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread

Re: The Exhaust Thread