Ignitech CDI question
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
Drunkn Munky
- Site Supporter
- Posts: 6313
- Joined: Thu May 01, 2008 9:37 am
- Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
- Location: Kent
Ignitech CDI question
With a standard cdi you need to connect the orange/blue rev limit wire to 12+ to stop it going into limp home mode, is this the case with the ignitech cdi's?
-
CMSMJ1
- Moderators
- Posts: 7161
- Joined: Thu May 01, 2008 9:42 am
- Bike owned: NC30-No9
- Location: Chesterfield, United Kingdom
-
Drunkn Munky
- Site Supporter
- Posts: 6313
- Joined: Thu May 01, 2008 9:37 am
- Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
- Location: Kent
Re: Ignitech CDI question
Good news, i dont have to unwrap the loom again then 
-
banoffee
- Site Supporter
- Posts: 1247
- Joined: Sat Aug 01, 2009 7:44 am
- Location: Surrey
- Contact:
-
Drunkn Munky
- Site Supporter
- Posts: 6313
- Joined: Thu May 01, 2008 9:37 am
- Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
- Location: Kent
Re: Ignitech CDI question
Yes mate, been playing with it today, my laptop doesnt have the 9 pin port so having to use a usb adaptor and it crashes when i try to connect. Im putting it down to my laptop tho as it crashes all the time. Its got the HRC map on it so that'll do for the meantimebanoffee wrote:have you got one yet?
-
banoffee
- Site Supporter
- Posts: 1247
- Joined: Sat Aug 01, 2009 7:44 am
- Location: Surrey
- Contact:
Re: Ignitech CDI question
Nice one. Seem to remember having to faff about a little with the USB lead drivers on mine too.
I settled for the 'HRC+2' map in the end and made the tacho reading more accurate and lowered the redline a smidge too.
Great toys
I settled for the 'HRC+2' map in the end and made the tacho reading more accurate and lowered the redline a smidge too.
Great toys
attention 2 detail - bike valeting and more
-
Indiana Jones
- Site Supporter
- Posts: 141
- Joined: Mon Jul 20, 2009 8:48 am
- Bike owned: XT600Z,'10 TE250 ,XS650 chop
- Location: Faugheen
- Contact:
Re: Ignitech CDI question
I just got my race bike running today with RLR ramair RVF carbs and Ignitech CDI.
Failed to communicate.
I don't think the driver is on the supplied disk??
Must contact RO.
Nearly ready for a dyno run.
Failed to communicate.
I don't think the driver is on the supplied disk??
Must contact RO.
Nearly ready for a dyno run.
-
geebus
- Site Supporter
- Posts: 58
- Joined: Fri Jan 07, 2011 7:56 pm
- Bike owned: 1990 VFR400 NC30 + SV650s
- Location: Inverclyde
- Contact:
Re: Ignitech CDI question
Whats the advantages of a Ignitech CDI?
Sorry if i seem a bit stupid but i am trying to build a race bike at the moment...and do it properly.
Sorry if i seem a bit stupid but i am trying to build a race bike at the moment...and do it properly.
-
Drunkn Munky
- Site Supporter
- Posts: 6313
- Joined: Thu May 01, 2008 9:37 am
- Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
- Location: Kent
Re: Ignitech CDI question
Go on the ignitech site, you can download it from there. Once installed check your hardware properties to see what port its communicating on then set the software to that com port. Worked for me, mines up and running nowindiaguy wrote:I just got my race bike running today with RLR ramair RVF carbs and Ignitech CDI.
Failed to communicate.
I don't think the driver is on the supplied disk??
Must contact RO.
Nearly ready for a dyno run.
Adjustable ignition advance, TPS mapping etc etc etc, check out there websitegeebus wrote:Whats the advantages of a Ignitech CDI?
Sorry if i seem a bit stupid but i am trying to build a race bike at the moment...and do it properly.
-
Indiana Jones
- Site Supporter
- Posts: 141
- Joined: Mon Jul 20, 2009 8:48 am
- Bike owned: XT600Z,'10 TE250 ,XS650 chop
- Location: Faugheen
- Contact:
Re: Ignitech CDI question
Got the driver. Should be communication tomorrow.