Broken Exhaust Stud Question

Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Post Reply
nc21man
Settled in member
Posts: 19
Joined: Mon May 19, 2008 6:42 pm
Location: guildford, surrey

Broken Exhaust Stud Question

Post by nc21man » Tue Jul 21, 2009 5:55 pm

I've read all the answers about how to get broken exhaust studs out, but the 2 that I've got are both broken right where they go into the head, so no chance of getting a nut welded on or similar. People have mentioned drilling them out, which I've tried, but I don't seem to be getting very far - what type of drill bit is best for this? I've just read on another site that solid carbide is probably the way forward, anybody agree? and if so, what's the best size to get?

cormac83
Settled in member
Posts: 16
Joined: Wed Dec 17, 2008 5:06 pm

Re: Broken Exhaust Stud Question

Post by cormac83 » Tue Jul 21, 2009 6:14 pm

just get some drill bits that you can use on metal - the size really depends on the size of the hole - you basically want to be able to drill the centre of the broken stud so you can get a torx bit hammered in the and then use socket wrench to get it out.

Just to warn you this does not always work 100% - and make sure you drill dead center as not to ruin the existing thread

hope this helps

crofty7
Settled in member
Posts: 50
Joined: Fri Jul 03, 2009 6:40 pm

Re: Broken Exhaust Stud Question

Post by crofty7 » Tue Jul 21, 2009 6:39 pm

To save yourself the pain i would take it to a pro who knows what he's doing. I guess its the front cylinders that one of the threads has sheared off :( You have to be very precise with your drilling. However you may be a braver man than me so good look ;)

nc21man
Settled in member
Posts: 19
Joined: Mon May 19, 2008 6:42 pm
Location: guildford, surrey

Re: Broken Exhaust Stud Question

Post by nc21man » Tue Jul 21, 2009 6:43 pm

Yeah - it's the front nearside ones - I have got the engine out at the moment, so I think a trip to the mender might be the best idea - hopefully they can do it without taking the head off! :pray: Anybody got any idea how much it might cost?

pptom
NWAA Supporter
NWAA Supporter
Posts: 141
Joined: Sun Jul 05, 2009 5:32 pm
Bike owned: Nc23 x 2 and an nc30

Re: Broken Exhaust Stud Question

Post by pptom » Tue Jul 21, 2009 7:09 pm

I had a similar problem on my car, snapped off just inside the head. I brought a set of stud extractors from e-bay for about £4, you have to drill a pilot hole then screw in the stud extractor which is essentially a very coarse reverse thread. The extractor eventually bites into the snapped stud, you keep turning and hey presto the stud comes out.

rcv4
Site Supporter
Site Supporter
Posts: 247
Joined: Fri May 15, 2009 11:11 pm
Bike owned: 2xnc30 nc35 rd200 xt500 dt250
Location: east yorkshire

Re: Broken Exhaust Stud Question

Post by rcv4 » Wed Jul 22, 2009 12:02 am

be carefull with the drilling and stud extractor,if you snap either one your in deep shit!!!!!

crofty7
Settled in member
Posts: 50
Joined: Fri Jul 03, 2009 6:40 pm

Re: Broken Exhaust Stud Question

Post by crofty7 » Wed Jul 22, 2009 7:06 pm

I second that. Best get it done properly first time instead of making it worse. Shouldn't cost too much just shop around. It will be loads cheaper and easier with your engine removed. :grin:

dave_c24
Settled in member
Posts: 139
Joined: Tue May 05, 2009 8:51 pm
Bike owned: 1991 vfr 400 nc30
Location: Newmarket

Re: Broken Exhaust Stud Question

Post by dave_c24 » Wed Jul 22, 2009 7:32 pm

i work for an engineering firm, and im sure it wuld not take more than 2 to 3 hrs to get out, think most places charge around £35 an hour. hope that helps.

they should need to take the head off, if need be they could just block the engine up on a mill and drill it out that way

cheers dave

Post Reply