end can options
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
Fluffy
- Settled in member
- Posts: 67
- Joined: Wed Apr 30, 2008 5:35 pm
end can options
ok who's shoehorned what onto which then??
My NC23 is now sporting a Quill from a zx7r!! ok its pointing the wrong way a little but my gawd it sounds soooo mcuh yummier
so what have you fitted witout going to a slip on fitting??
My NC23 is now sporting a Quill from a zx7r!! ok its pointing the wrong way a little but my gawd it sounds soooo mcuh yummier
so what have you fitted witout going to a slip on fitting??
-
Matchlessman
- Familiar Member
- Posts: 261
- Joined: Fri May 02, 2008 12:29 pm
- Location: Stroud, Glos
Re: end can options
I've got a micron cabonfibre can on mine. combined with the GF stainless downpipes, it sounds fantastic. :D
Too many bikes, so little time!
-
cress87
- Settled in member
- Posts: 81
- Joined: Wed Apr 30, 2008 10:12 pm
- Bike owned: NC23 CBR400RR
- Location: Norwich
Re: end can options
Was that a direct fit? Bolt on?Fluffy wrote:ok who's shoehorned what onto which then??
My NC23 is now sporting a Quill from a zx7r!! ok its pointing the wrong way a little but my gawd it sounds soooo mcuh yummier
so what have you fitted witout going to a slip on fitting??
-
Fluffy
- Settled in member
- Posts: 67
- Joined: Wed Apr 30, 2008 5:35 pm
Re: end can options
a very small amount of filing was required and it bolted on.... its not quite pointing the right way tho as although the stud spacing is 98% the same they are rotated a few degress different, the exit port currently points accross my rear tyre
(one way to warm it i suppose!)
so only really works with a round can.... which is going to get shortened and in that process the exit port rotated a little :D
(one way to warm it i suppose!)
so only really works with a round can.... which is going to get shortened and in that process the exit port rotated a little :D
-
spudhed
- Settled in member
- Posts: 37
- Joined: Wed Apr 30, 2008 4:16 pm
Re: end can options
my 29 is running GF pipes with an art stainless bolt on, it sounds fantastic, although the neighbors dont agree! if im honest id prefer a titanium can but i dont know of any that fit
-
missinNZ
- Settled in member
- Posts: 185
- Joined: Sat May 03, 2008 5:17 pm
- Location: isle of wight
Re: end can options
stainless steel custom 4 to 1 pipes with carbon art can purrs like a cat
-
rojer386
- Settled in member
- Posts: 34
- Joined: Fri May 02, 2008 4:09 pm
Re: end can options
I have stainless steel 4-1 then a slip on can, not sure of the make. I really want to change the can but I'm having problems finding a slip on to replace it!
-
honda312
- Settled in member
- Posts: 2
- Joined: Sun May 25, 2008 11:03 pm
Re: end can options
I have got a 10.5 inch str8 through stubby can on my babyblade (NC23) bought it of ebay spent ages finding one i liked there is no markings on it so i think its custom made for my bike looks sweet though so if you get one made or find one get it also it sounds lush much different sound to a longer can and looks the Bo***cks!!
-
Sligeach
- Site Supporter
- Posts: 690
- Joined: Wed Apr 30, 2008 4:02 pm
- Bike owned: '90 NC30 - '12 Stripe R
- Location: Sutton, Surrey
- Contact:
end can options
that straight through i think is a guy off the MSCninjas forum
i'll see if i can find the link
i'll see if i can find the link
-
leopard_pagan
- Senior Member
- Posts: 1184
- Joined: Thu May 01, 2008 6:42 am
- Bike owned: CBR400/600 Fighter
- Location: Mildenhall-Suffolk
- Contact:
Re: end can options
*IF* the can has a riveted end, why not drill the rivets, rotate the end piece and re-rivet in place.....