RVF400 Project - A step in a different direction.

TZcRank · Post by **TZcRank** » Mon Jan 21, 2019 9:29 am

Thank you

ZippiT · Post by **ZippiT** » Tue Jan 22, 2019 5:36 am

More parts! Everyone loves parts! :D

Translogic Micro Dash
RVF400 HRC Oil cooler
CBR600F4i Oil cooler (replaced by above)
Stubby oil filter HF147
CBR600RR 2016 Forks
CBR600RR Tokico calipers

RoninZX-10R · Post by **RoninZX-10R** » Thu Jan 24, 2019 8:22 pm

That new front end will look so nice on the RVF. Can't wait to hear what the big bore motor is like to ride, that thing will fly!!

ZippiT · Post by **ZippiT** » Mon Jan 28, 2019 4:54 am

RoninZX-10R wrote: Thu Jan 24, 2019 8:22 pm That new front end will look so nice on the RVF. Can't wait to hear what the big bore motor is like to ride, that thing will fly!!

I can't wait either. Can't wait to take it through some twisties

RoninZX-10R · Post by **RoninZX-10R** » Tue Feb 19, 2019 7:52 pm

Have you been able to make any further progress? Really looking forward to seeing more photos.

ZippiT · Post by **ZippiT** » Sun Mar 03, 2019 8:22 am

RoninZX-10R wrote: Tue Feb 19, 2019 7:52 pm Have you been able to make any further progress? Really looking forward to seeing more photos.

Mainly gathering parts for the build. I've ordered the Carrillo rods from Mike, and should be here this month. Still need to get some crank/rod bearings, piston rings and modified head gaskets before I can start assembling the engine.

More things gathered:
NC21 sprocket cover
NC21 clutch slave cylinder (May upgrade it in the future)
NC21 push rod
RC19S clutch master cylinder
CBR600RR left hand switch-block
CBR1000RR right hand switch-block
RVF400 pillion pegs, to replace the VFR400 ones
VFR400 shock reservoir bracket
Full engine rebuild set
EBC heavy duty clutch
Engine casings bead-blasted

RoninZX-10R · Post by **RoninZX-10R** » Tue Mar 05, 2019 1:01 am

Looks like you've been spending a lot of time collecting bits! Have you had the cylinders bored out yet?

ZippiT · Post by **ZippiT** » Tue Mar 05, 2019 4:52 am

RoninZX-10R wrote: Tue Mar 05, 2019 1:01 am Looks like you've been spending a lot of time collecting bits! Have you had the cylinders bored out yet?

Yep, pics on page 1

Vincent · Post by **Vincent** » Thu Mar 07, 2019 12:52 am

What did you end up doing with the GP-T kit? Do you know if the fitment is the same (or similar) for a VFR400?

ZippiT · Post by **ZippiT** » Thu Mar 07, 2019 7:08 am

Vincent wrote: Thu Mar 07, 2019 12:52 am What did you end up doing with the GP-T kit? Do you know if the fitment is the same (or similar) for a VFR400?

They do a GPT kit for the VFR. TYGA Make them. The tail is not a GPT kit piece tho.

RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.

Re: RVF400 Project - A step in a different direction.