gk 76a sp
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
stevo400
- Settled in member
- Posts: 32
- Joined: Mon Mar 28, 2016 2:23 pm
- Bike owned: 90 suzuki gsxr400 sp
gk 76a sp
Hallo to all!!!
I'm posting this on its own to see if I can get more response. I have a gk76a sp. My bike idles good but refuses to rev over 6k rpm. I have no tps on my carbs could this be the cause?
Thanks in advance.
I'm posting this on its own to see if I can get more response. I have a gk76a sp. My bike idles good but refuses to rev over 6k rpm. I have no tps on my carbs could this be the cause?
Thanks in advance.
-
moforockband
- Familiar Member
- Posts: 378
- Joined: Wed Jun 03, 2015 9:41 am
- Bike owned: GK73a SP CRM250 mk3
Re: gk 76a sp
- Carbs flooding, have you replaced the o rings - 76's need their carbs to have sound o rings, or else it will run really rich, damage engines etc etc.
- Check you have no air restriction
- Check the vacuum slides are sound, free to operate
Nick.
- Check you have no air restriction
- Check the vacuum slides are sound, free to operate
Nick.
-
stevo400
- Settled in member
- Posts: 32
- Joined: Mon Mar 28, 2016 2:23 pm
- Bike owned: 90 suzuki gsxr400 sp
Re: gk 76a sp
Hai Nick thanks for the reply, all new o rings, gonna replace the slides today plus the diaphragms. Will let you know of the outcome. Thanks
-
stevo400
- Settled in member
- Posts: 32
- Joined: Mon Mar 28, 2016 2:23 pm
- Bike owned: 90 suzuki gsxr400 sp
Re: gk 76a sp
So the carbs on my sp is 35mm and uses tps, today I got a tps off a set of 33mm carbs, unfortunately I can't use anything else off the set, ill get another set of 35s tomorrow but they don't use tps so I'm gonna check if I can use parts from it to rebuild to mine, is there any major difference between the two 35s anyone know about? Also the 3wires from the tps to cdi has been removed anyone know what order they go back on?
-
Variablevalves suck
- Site Supporter
- Posts: 1922
- Joined: Sat Jan 24, 2009 10:52 am
- Bike owned: GSXR Carb o'ring kits supplied
- Location: Stoke-on-trent
Re: gk 76a sp
Sure they run with no tps connected, ive ran my vvc bandit.
read that it only retards the ignition at low throttle position or similar.
33 and 35 mm carb bodies are the same but 35 is over bored, one of the old members machined 33mm out with no problems.
read that it only retards the ignition at low throttle position or similar.
33 and 35 mm carb bodies are the same but 35 is over bored, one of the old members machined 33mm out with no problems.
-
stevo400
- Settled in member
- Posts: 32
- Joined: Mon Mar 28, 2016 2:23 pm
- Bike owned: 90 suzuki gsxr400 sp
Re: gk 76a sp
I rebuilt the carbs today, the set I got today got different type of jet needles and needle jet, but I built it all over to my old set, will set float levels tomorrow and give it a go, if anyone can help maybe with a picture of where the black, blue and red wires from the tps connect to the cdi. Any help will be appreciated.