RO Road Needle question
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
mattvfr400
- Settled in member
- Posts: 47
- Joined: Thu Dec 31, 2015 12:48 pm
RO Road Needle question
Does Ricks needle set need 2 0.5 washers or 1? I have 2 on the standard needles for the fueling.
Cheers
Cheers
-
fatpete
- Site Supporter
- Posts: 53
- Joined: Wed Apr 30, 2008 4:55 pm
- Bike owned: NC35 (RIP), CBR900RR, NC 30
- Location: Luton, UK
- Contact:
Re: RO Road Needle question
1 I believe, that's what I am running anyway.
-
mattvfr400
- Settled in member
- Posts: 47
- Joined: Thu Dec 31, 2015 12:48 pm
Re: RO Road Needle question
Cheers fella. Did you notice much improvement after installing them?fatpete wrote:1 I believe, that's what I am running anyway.
-
fatpete
- Site Supporter
- Posts: 53
- Joined: Wed Apr 30, 2008 4:55 pm
- Bike owned: NC35 (RIP), CBR900RR, NC 30
- Location: Luton, UK
- Contact:
Re: RO Road Needle question
Not a huge amount as I did several other mods at the same time so it's hard to say what effect they made, but the originals were worn so needed replacing anyway. Certainly not found any problem with them, but the bike does need some dyno time to get it just so.
Happy I got them but will be interested to hear if they make much of a difference for you.
Happy I got them but will be interested to hear if they make much of a difference for you.
-
RickOliver
- Site Supporter
- Posts: 489
- Joined: Sun May 11, 2008 8:55 am
Re: RO Road Needle question
Those needles are a straight drop in replacement for the originals so use the standard 0.5mm stainless washer but no extras...
Rick
Rick
-
richyrd5
- Regular Member
- Posts: 743
- Joined: Fri Feb 21, 2014 1:31 pm
Re: RO Road Needle question
Rick.are the shims needed for the hrc kit a.b.c needles?(rvf carbs)
-
mattvfr400
- Settled in member
- Posts: 47
- Joined: Thu Dec 31, 2015 12:48 pm
Re: RO Road Needle question
Appreciate that Rick. Cheers.RickOliver wrote:Those needles are a straight drop in replacement for the originals so use the standard 0.5mm stainless washer but no extras...
Rick
-
RickOliver
- Site Supporter
- Posts: 489
- Joined: Sun May 11, 2008 8:55 am
Re: RO Road Needle question
The RVF kit needles have a circlip and 3 grooves for height adjustment (the VFR ones just have a plain flange built into the needle like the stockers) - the grooves are 1mm apart so the kit just has 4 x 0.5mm spacers to give you an optional height increment of `half a groove` for fine tuning if required.
-
richyrd5
- Regular Member
- Posts: 743
- Joined: Fri Feb 21, 2014 1:31 pm
Re: RO Road Needle question
Excellent.thanks chap..RickOliver wrote:The RVF kit needles have a circlip and 3 grooves for height adjustment (the VFR ones just have a plain flange built into the needle like the stockers) - the grooves are 1mm apart so the kit just has 4 x 0.5mm spacers to give you an optional height increment of `half a groove` for fine tuning if required.