All Balls bearings

Post by **Davez29** » Wed Jul 22, 2015 5:10 pm

Just a heads up, I had to buy a set of rear wheel bearings and the AllBalls pack which is marked cbr400 (1991-1998) does not fit the nc29. The correct fitmant should say 6004, the AllBalls says 6303 and is a good few mil wider.

Post by **Toman123** » Sat Jul 25, 2015 12:31 pm

Thanks for the info dave.. Was just about to order the all ball kit from ebay. Will stay clear.

Post by **Davez29** » Sat Jul 25, 2015 1:27 pm

Yep I was the sucker who did, mainly wanted those as I have AllBalls in my steering head for the last couple of years and they seem OK.

Now I have generic cheopos but they only got to last till crimbo as I'm going to get the wheel coated.

Post by **Toman123** » Sun Jul 26, 2015 10:44 am

They will do you for a while alright.. I'm getting my wheels coated next week and the forks rebuilt so i might go for pyramid wheels and steering bearings also got there fork seal kit to.
They seem good quality anyway.

Post by **Davez29** » Sun Jul 26, 2015 4:57 pm

I just noticed a shop near me who I went to and tried to buy the allballs kit from has put them on ebay and someone has bought them for the 29, very odd as if its the same kit he showed me and I assume it is, he will have an unhappy customer when he finds the wrong sized bearings in the pack.

To be honest I try to go OEM nowadays but for some daft reason it slipped my mind as I was trying to get the bearings quickly but because of errors it took longer than going to David Silver.

Post by **willandrip** » Sun Jul 26, 2015 5:08 pm

Durka Durka wrote:I just noticed a shop near me who I went to and tried to buy the allballs kit from has put them on ebay and someone has bought them for the 29, very odd as if its the same kit he showed me and I assume it is, he will have an unhappy customer when he finds the wrong sized bearings in the pack.

Hunters ?

If so...the young un won't bat an eye . !

Post by **Davez29** » Sun Jul 26, 2015 5:15 pm

Hunters ?

If so...the young un won't bat an eye . !

Yep, maybe they did not believe me and are doing a test sale.

Post by **willandrip** » Sun Jul 26, 2015 5:23 pm

They won't fook about like that....not worth the bother.

They will however , be using the info sheet that came with the product or order .
Hunters does a lot of "All Balls" kit stuff.
Also; "All Balls" is a U.S. company and will be using US spec which MAY be different to UK/Grey tackle r.e. fitment

Frankly ;unless the kit has a particular special part , it is far and away cheaper to by generic bearings....the quality would be similar. Headstock bearings in particular.

Post by **Davez29** » Sun Jul 26, 2015 5:40 pm

I suppose its down to allballs and their spec sheet, Hunters or any other retailer can only sell what they believe is the right kit sent by the manufacturers. I suppose it could have been wrongly labelled or packed wrong. So if anyone does buy them let us know what bearings you get. Hunters did spend time trying to sort it for me so I have no problems with them.

Post by **willandrip** » Sun Jul 26, 2015 5:45 pm

They are about the last "Old School" venture left on a street that once had over 30 motorcycle specific shops.

I use them a lot where feasible.....and nearly did time with the founder !

All Balls bearings

All Balls bearings

Re: All Balls bearings

Re: All Balls bearings

Re: All Balls bearings

Re: All Balls bearings

Re: All Balls bearings

Re: All Balls bearings

Re: All Balls bearings

Re: All Balls bearings

Re: All Balls bearings