NC35 Carbs on NC30 ?

[royster81]

i would be really interested to know how much of a mid range increase do they give over '30 carbs ,if someone had graphs showing this i would be greatful

Once the new system arrives you can look at my dyno print-out

are you going to get the operator to run both sets of carbs ?

[viper_biker]

I have other printouts with the 30 carbs fitted so we can see the difference there. Wonder if the Rick O CDI will nake any difference, that's something I'd consider.

[Sligeach]

just got an email from David Silvers, for the little brown y-piece they want 19.99 and a fiver postage. so at that rate i could jet get a set of 35 carbs off ARBmoto for 50 and sell off my carbs for spares

[stevie]

you dont need the 35 cable as i said you just need to modify the bracket, ill try to find the drawing i had, i cant remember who gave it to me it was someone from this site but that was years ago when i fitted mine, i wouldnt recomend removing the return cable as if your throtle cable isent properly lubricated or gets pinched you will get stuck on an open throttle, the return spring isnot that strong so beware. i dont know the exact midrange increase as i done other mods but i could feel the differance, the bike would spin the rear in second, peak power was up allmost 9bhp but iv got the 35 carbs with full hrc carb kit running 150/152 mj, the "b" needles on the top clip, hrc emulsion tubes, slide springs and bell mouths, hrc air box and air tray with modifyed filter for road use, k&n crank case filter, top rad lowered 15mm to open up inlet, nc35 cams, full tyga exhaust system, ect.. i have tryed more set ups than i care to remember and this one gives the best spread of power with no flat spots, but my fuel consumtion had droped dramaticly, iv gone from getting 110 miles per tank to around 60, it may not be so hi if i took it easy but wheres the fun in that?

[royster81]

just got an email from David Silvers, for the little brown y-piece they want 19.99 and a fiver postage. so at that rate i could jet get a set of 35 carbs off ARBmoto for 50 and sell off my carbs for spares

you could try rick for the carb part as he helped me out a year or so ago with something similar

[CMSMJ1]

just got an email from David Silvers, for the little brown y-piece they want 19.99 and a fiver postage. so at that rate i could jet get a set of 35 carbs off ARBmoto for 50 and sell off my carbs for spares

I have 3 sets of '30 carbs on my garage shelf - send me a pic or the fiche ref and I will send you one gratis. When I make it to your island you can buy me a pint..lol

[Sligeach]

I have 3 sets of '30 carbs on my garage shelf - send me a pic or the fiche ref and I will send you one gratis. When I make it to your island you can buy me a pint..lol

Cheers Buddy
the part number i have is: 16027-ML0-004 - number changes to 16026-KV0-014
its the part number 5 on my Fiche

you can go to Ireland and get a pint but one of the norn iron members will have to pay for it, because i wont be around, i live in south london!! come on down

[CMSMJ1]

I have 3 sets of '30 carbs on my garage shelf - send me a pic or the fiche ref and I will send you one gratis. When I make it to your island you can buy me a pint..lol

Cheers Buddy
the part number i have is: 16027-ML0-004 - number changes to 16026-KV0-014
its the part number 5 on my Fiche

you can go to Ireland and get a pint but one of the norn iron members will have to pay for it, because i wont be around, i live in south london!! come on down

roger that matey - will get in the garage and get one out to you tomorrow. I deffo have a few of them! Pintwise...well, am sure I will see you at a track sometime this decade...I will blag a schooner off you then

So you not going to get 35 carbs any more? They do work...could be tempted to sell mine seeing as no9 is going to be made into a race bike... short stacks..big jets..you know it makes sense

[royster81]

no9 is going to be made into a race bike... short stacks..big jets..you know it makes sense

easy buddy you know it does... lol... go on you legend.....