Six Hundred and Sixty

Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Post Reply
Maelstrom
Site Supporter
Site Supporter
Posts: 536
Joined: Tue Aug 16, 2011 3:10 pm
Bike owned: MC22, 3TJ1
Location: Thailand
Contact:
Contact Maelstrom
Re: Six Hundred and Sixty

Post by Maelstrom »

nice picture EC :grin:
I have no idea what it is, but it looks like an oil restrictor with that small hole in the centre.
Email that pic to BDK they will know.
Carb seal kits in viton & other parts
https://litetek.co
Top
4StrokePete
Settled in member
Posts: 28
Joined: Mon Jun 01, 2009 7:38 am
Bike owned: FZR400RR SP
Location: Gold Coast
Re: Six Hundred and Sixty

Post by 4StrokePete »

maelstrom wrote:nice picture EC :grin:
I have no idea what it is, but it looks like an oil restrictor with that small hole in the centre.
Email that pic to BDK they will know.

Pretty sure it is an oil restrictor , 3TJ parts book , no 1HX-15138-00
it sits in an oring no 93210-12152
It is between the upper and lower cases so you will need to split them again, bummer !!!
Top
Evilchicken0
Site Supporter
Site Supporter
Posts: 5374
Joined: Tue Apr 29, 2008 8:59 pm
Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
Location: Lundin Taan
Re: Six Hundred and Sixty

Post by Evilchicken0 »

Great news :(
At least I can sort the cam chain while I'm down there .... and I left in the two bolts that are only accessable when you take the barrels off .... happy days
Top
Maelstrom
Site Supporter
Site Supporter
Posts: 536
Joined: Tue Aug 16, 2011 3:10 pm
Bike owned: MC22, 3TJ1
Location: Thailand
Contact:
Contact Maelstrom
Re: Six Hundred and Sixty

Post by Maelstrom »

Every cloud has a silver lining, EC. You can always take the opportunity to fit the new seal rather than run the risk with the Franken version.
Carb seal kits in viton & other parts
https://litetek.co
Top
Evilchicken0
Site Supporter
Site Supporter
Posts: 5374
Joined: Tue Apr 29, 2008 8:59 pm
Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
Location: Lundin Taan
Re: Six Hundred and Sixty

Post by Evilchicken0 »

Good point. In my defense it's the first engine I've built so I guess I'll remember what this is and where it goes.
Top
Evilchicken0
Site Supporter
Site Supporter
Posts: 5374
Joined: Tue Apr 29, 2008 8:59 pm
Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
Location: Lundin Taan
Re: Six Hundred and Sixty

Post by Evilchicken0 »

Last night I tidied up the garage, built a table / bench and put the engine on it. TBH the table is a bit to big, I can still get the bikes in easily but I think I might get rid of it after the engines done, next Christmas then :grin:

Image
Top
Evilchicken0
Site Supporter
Site Supporter
Posts: 5374
Joined: Tue Apr 29, 2008 8:59 pm
Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
Location: Lundin Taan
Re: Six Hundred and Sixty

Post by Evilchicken0 »

So, the clutch holding tool turned up today so I could make a start. The one thing I didn't want to do was take the barrels off mainly because I don't like getting them on with the piston rings, so thank you to the inventor of universal links

Image
Top
Evilchicken0
Site Supporter
Site Supporter
Posts: 5374
Joined: Tue Apr 29, 2008 8:59 pm
Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
Location: Lundin Taan
Re: Six Hundred and Sixty

Post by Evilchicken0 »

Had a look about and I've also been onto Simply Bearings to try and find an oilseal. You can get a pain rotary seal 26x40x8_TC easily but it doesn't have the locating 2x2mm flange on the back. I don't know if it's possible to add one to the the plain seal or not, but I think I'm going to go with Frankenseal for now.

Oh and the barrels have to come off because of the rear camchain guide.
Top
Evilchicken0
Site Supporter
Site Supporter
Posts: 5374
Joined: Tue Apr 29, 2008 8:59 pm
Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
Location: Lundin Taan
Re: Six Hundred and Sixty

Post by Evilchicken0 »

If I have a few of these seals made up roughly how many people would be interested ???
Top
Alex.
Settled in member
Posts: 212
Joined: Wed Jul 23, 2008 3:33 pm
Location: Rainham, Kent.
Re: Six Hundred and Sixty

Post by Alex. »

Me! Me!

Any news from BDK about the crank?

Alex.
Top
Post Reply

Return to “Yamaha - Workshop”