NC30 Carb Balancing trickery.

britaxcooper · Post by **britaxcooper** » Mon Jan 19, 2009 7:14 pm

did anyone get around to doing a guide.

Post by **viper_biker** » Mon Jan 19, 2009 7:20 pm

Sorry mate, I never got out to the garage all weekend. I'll try and borrow a set on NC carbs and let you all see how it's done. There's no point in my pulling off the carbs that are already fitted.

ryancusick · Post by **ryancusick** » Fri Feb 06, 2009 5:08 pm

Tried to balance my carbs today. Got the back 2 and the front 2 done but when I went to sync the 4 together the bike started revving up to 5k. Idle speed adjuster wouldnt effect it and i tried re-adjusting the adjusting screws with no luck. Any suggestions??

Cheers

ryancusick · Post by **ryancusick** » Sat Feb 07, 2009 7:06 pm

Drill bit works great!!!!

Richie1743 · Post by **Richie1743** » Wed Jan 18, 2012 11:34 pm

A big thank you for this thread.
I got a new set of carbs before Christmas and put them on the bike and started it for the first time in 5 years with the aid of ... "StartuBastard" ... ran it for 30-40 minutes to get her upto temp and throttle range.. all great...
the next day... nothing... not even an attempt at starting...
So yesterday decided to do a search on this site to enlighten me...
I came across this thread, and followed a few suggestions...

Drained the fuel tank (as the fuel that was in came out of a jerry can I had laying about for a couple of 3 years...) and put some fresh Go go juice in it.

Removed the spark plugs and deep cleaned them, with heat from cooker hob and an old mess tin. wire brush and regapped them.

reset the carb setting screws as they were 3-4 full turns in... so turned them in gently until they bottomed out then backed them out 1.75 turns.... thank Goodness for extra long screwdrivers :0)

Full choke, ignition, no throttle... and By Christ She Started first press of the Tit :0)
I lov ( . Y . ) me :0)

So once again...
A BIG THANK YOU.

Richie.

Post by **28hodge** » Thu Jan 19, 2012 8:29 am

Richie, i have this thread saved in my favourites, i used it so many times trying to get my NC30 to run correctly, it too had stood for a long time, 8-10 years and thanks to greybike its running a well as i can hope.

Glad youve got it running.

Post by **royster81** » Thu Jan 19, 2012 7:16 pm

Did anyone ever do a step by step on this ?

krisztian_andre · Post by **krisztian_andre** » Fri Jun 08, 2012 2:07 pm

Will this http://www.ekmpowershop20.com/ekmps/sho ... l-81-p.asp do the job?

Post by **viper_biker** » Fri Jun 08, 2012 3:12 pm

royster81 wrote:Did anyone ever do a step by step on this ?

Don't think so, but I can see about doing one this weekend.

hardnutdvd · Post by **hardnutdvd** » Fri Jun 08, 2012 3:45 pm

krisztian_andre wrote:Will this http://www.ekmpowershop20.com/ekmps/sho ... l-81-p.asp do the job?

im pretty sure thats exactly what you need

NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.

Re: NC30 Carb Balancing trickery.