Track mods

Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Post Reply
Bike_Nut
Settled in member
Posts: 180
Joined: Sun Oct 19, 2008 6:48 pm

Track mods

Post by Bike_Nut » Fri Oct 07, 2011 8:48 pm

I love modifying bikes, but I also love standard restored bikes. As such, when I bought a bike for spares and found it too good to break but too far away from being returned to the road, I got thinking about returning my old faithful NC30 to standard and doing a track bike to supplement.

This means I have single seat, technoflex shock, ebc rotors, braided hoses, half system and 17" rear ready for the project. The nc30 motor has low miles and looks good so that will stay, but will need a few mods and this is where help is needed.

I am thinking of doing the gsxr charging system mod, removing the quietening scissor gears, a little bit of head work etc. Are these all worthwhile mods?

Also, I am planning to keep an air filter on the bike but am unsure of the best carb setup. Do the NC3 carbs help with midrange or should I stick with the NC30 ones?

Thanks for any tips
Shane

User avatar
Drunkn Munky
Site Supporter
Site Supporter
Posts: 6313
Joined: Thu May 01, 2008 9:37 am
Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
Location: Kent

Re: Track mods

Post by Drunkn Munky » Fri Oct 07, 2011 9:28 pm

Well if its just going to be a dedicated track bike and you don't have unlimimted funds to throw at it forget the gsxr charging kit, its a big expense for some you don't need, just remove the charging system period.

Nc35 carbs have better midrange annd some say fuel nicer but a trackbike will be living at 8k + most of the time so again not needed, the 30 carbs are bigger so in theroy should work better at high rpm which is where you want it.

Spend the money headwork and removing the quitening gears, pretty sure the head needs skimming if you remove them anyway, or something along those lines. Then you might aswell run the hrc setup or ram air for a bit more expense, you don't need a air filter for track bikes.

Have fun :)

User avatar
CMSMJ1
Moderators
Moderators
Posts: 7152
Joined: Thu May 01, 2008 9:42 am
Bike owned: NC30-No9
Location: Chesterfield, United Kingdom

Re: Track mods

Post by CMSMJ1 » Fri Oct 07, 2011 9:49 pm

What he said.

Total loss. Decent suspension and brakes.
Tracktime..winner!
IMPERATOR REX ANGLORUM

The V4 is the law..

NC30 - No9 - my old mate

spanky
Site Supporter
Site Supporter
Posts: 89
Joined: Wed Sep 23, 2009 1:47 pm
Bike owned: rvf trackbike, 600rr

Re: Track mods

Post by spanky » Fri Oct 07, 2011 11:43 pm

17" rear and linkage for tyre choice, decent front brakes and fork springs, rear shock and fixed rearests instead of the springy standard ones.

My blown engine had been de-scissor geared. Did it spin up faster? Not sure. Did it idle like a bag of spanners? Oh yes....

Bike_Nut
Settled in member
Posts: 180
Joined: Sun Oct 19, 2008 6:48 pm

Re: Track mods

Post by Bike_Nut » Sun Oct 09, 2011 10:15 am

I was thinking about keeping the charging system and running a daytime mot. As I wont be racing competitively the convienience of a starter swings it for me.

How much running could you get from a full charge on a healthy battery?

spanky
Site Supporter
Site Supporter
Posts: 89
Joined: Wed Sep 23, 2009 1:47 pm
Bike owned: rvf trackbike, 600rr

Re: Track mods

Post by spanky » Sun Oct 09, 2011 8:38 pm

Mine had a starter motor and fuel pump and still lasted all 7 sessions with only an hour on the optimax at lunchtime. I'm not even sure it needed that tbh.

Bike_Nut
Settled in member
Posts: 180
Joined: Sun Oct 19, 2008 6:48 pm

Re: Track mods

Post by Bike_Nut » Thu Oct 13, 2011 9:01 pm

Thanks for the replies - I think I will go total loss for a start, just use a good lightweight battery. Getting excited about the idea of a nice light track bike

Bike_Nut
Settled in member
Posts: 180
Joined: Sun Oct 19, 2008 6:48 pm

Re: Track mods

Post by Bike_Nut » Sun Oct 16, 2011 9:36 pm

Another one for those in the know. I have 2 sets of forks, and early set and a later set with rebound adjustment. Although the earlier forks are needing new seals the stanchions are in very good condition. The later forks are not leaking but they have more pitting. I know both forks can be improved, but logic tells me to stick with the later ones. If the pitting is a problem I guess a rechrome can sort them. Would this be the best option?

User avatar
Drunkn Munky
Site Supporter
Site Supporter
Posts: 6313
Joined: Thu May 01, 2008 9:37 am
Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
Location: Kent

Re: Track mods

Post by Drunkn Munky » Sun Oct 16, 2011 9:44 pm

Your logic serves you right ;)

Bike_Nut
Settled in member
Posts: 180
Joined: Sun Oct 19, 2008 6:48 pm

Re: Track mods

Post by Bike_Nut » Fri Oct 21, 2011 6:40 pm

Some more silly questions.

For track bikes do you remove the ignition key etc and just rely on the off switch on the bars? Its a bit more weight removed after all (That and a lock set seems to fetch good money on ebay lol)

Also, do you just make a little cover for where the speedo drive bolts onto the engine?

Will post some pictures soon

Thanks

Post Reply