xivlia's thread of nc30 problems and questions

xivlia · Post by **xivlia** » Tue Oct 04, 2011 7:21 pm

hmm okay :\ i might buy some new ones later on then :)

xivlia · Post by **xivlia** » Tue Oct 04, 2011 7:22 pm

OKAY! ive not got even a BIGGER problem....the screw snapped at the front part now...and it looks muuch harder to get out....any ideas on that one? the front part as i can see is just a direct connection to the valve box cover. so there is no manifold. am i pretty much fucked? :\

amorti · Post by **amorti** » Tue Oct 04, 2011 10:45 pm

xivlia wrote:OKAY! ive not got even a BIGGER problem....the screw snapped at the front part now...and it looks muuch harder to get out....any ideas on that one? the front part as i can see is just a direct connection to the valve box cover. so there is no manifold. am i pretty much fucked? :\

Pretty much, yes. Get the engine out and take it to any local engineering shop you can find. They can remove all the studs and tap out the holes. Or just remove the damaged ones but you will be gutted when you refit the engine and snap an old stud that's now been weakened. Once that is done, replace any studs for brand new OE parts. Be warned, using cheap bog standard stud is a recipe for doing it all a second time.

If you try to get it out on your own, there is a good chance you will make it worse, then the bill just gets worse. Unless of course you have good stud extractor tools (leave the ez-outs alone!!) or can weld a nut to the snapped studs youself.

ps. it's a bit late now but if you'd asked before attempting it, we'd have warned you to soak all the studs in plus-gas for several days before attempting to remove them. And told you the best tools to use. Studs usually snap due to a) corrosion and b) people using the wrong tools and applying force up or down, rather than around, IYSWIM.

Post by **CMSMJ1** » Wed Oct 05, 2011 8:55 am

Hold your horses mate!

Have you "just" snaped the 2 bolts on the picture above?

not the little stubby pipe that joins to the motor? if you have not got the right tools, then get some before you try and do this - it is a lesson that we all learn and it is a total pain in the arse.

Post by **Drunkn Munky** » Wed Oct 05, 2011 9:32 am

xivlia wrote:OKAY! ive not got even a BIGGER problem....the screw snapped at the front part now...and it looks muuch harder to get out....any ideas on that one? the front part as i can see is just a direct connection to the valve box cover. so there is no manifold. am i pretty much fucked? :\

OK relax, you need to be a bit clearer on what you've actually snapped, system to rear manifold studs or the manifold to head studs? Either way its not the end of the world and with the RIGHT tools its not that much of a headache, just strip the back end down and get the subframe, shock etc out the way then you got a fighting chance of getting to it.

amorti · Post by **amorti** » Wed Oct 05, 2011 10:13 am

CMSMJ1 wrote:Hold your horses mate!

Have you "just" snaped the 2 bolts on the picture above?

not the little stubby pipe that joins to the motor? if you have not got the right tools, then get some before you try and do this - it is a lesson that we all learn and it is a total pain in the arse.

IMHO if he's referring to the exhaust manifold studs as "screws" then there is a strong chance that trying to fix this himself would be a steep and expensive learning curve.

Post by **CMSMJ1** » Wed Oct 05, 2011 11:03 am

I agree..but you got to learn the hard way sometimes.

Post by **philfingers** » Wed Oct 05, 2011 11:11 am

xivlia wrote:OKAY! ive not got even a BIGGER problem....the screw snapped at the front part now...and it looks muuch harder to get out....any ideas on that one? the front part as i can see is just a direct connection to the valve box cover. so there is no manifold. am i pretty much fucked? :\

put you're location on your profile, then if someone is local to you they may help you out!

xivlia · Post by **xivlia** » Wed Oct 05, 2011 12:22 pm

just to clarify things...this is my problem now guys... its the frong right (while sitting onthe bike) connection to the downpipe..

Post by **philfingers** » Wed Oct 05, 2011 12:38 pm

you're far enough away! I'd strip it down so that you can get access then you need to find someone who can do it for you, either a bike shop or a machine shop. if it's the latter then they may well want the engine out.
If it was mine and i had been unfortunate enough to snap them off I'd use a very small drill and go in through the centre, then enlarge it and tap it out. I've never found eze out's any good in small diameters. if there's anything left at all sticking out the block I'd try and weld a nut on. this gives you something to grab hold off but also put a lot of heat into the area in the process which helps free it off. If you go the weldling route then disconnect the ignition module (CDI) etc.
I have a mate in St Andrews who could probably help if you were stuck, but he's far from you and he will charge, but he's good.

xivlia's thread of nc30 problems and questions

Re: can anyone help with restrictor kit installation? NC30

Re: HELP! screw snapped at the exhaust manifold!

Re: HELP! screw snapped at the exhaust manifold!

Re: HELP! i have a BIGGER problem now!

Re: HELP! screw snapped at the exhaust manifold!

Re: HELP! i have a BIGGER problem now!

Re: HELP! i have a BIGGER problem now!

Re: HELP! screw snapped at the exhaust manifold!

Re: HELP! i have a BIGGER problem now!

Re: HELP! i have a BIGGER problem now!