not running right on all 4..

DK-Tandy · Post by **DK-Tandy** » Sun May 29, 2011 4:55 pm

so yeturday i was fiddling with my bike preventing the rattle at 4k to 6k revs. so i put it all together then dropped it.. i say dropped it, it fell over the other way and i placed it on the floor as i had the strength the lower it slowly but not enough to pick it up from a 35degree angle.. i then picked it up as you do and started it to see if i had stopped the rattle..

it wasnt running on all 4 cylinders

as you sit on the bike, cylinder 3 was working.
i took it for a whiz around the block and yippee, the cylinder had kicked back in and it was working, it then ran like a dream all night..

come to go to work today and it was only running on 3 cylinders again.. i presume is was 1 2 and 4. Got about .1 km up the road and i could feel a change as like the cylinder had kicked back in :)

done my shit shift at work and started the bike up to come home..

running on 3 cylinders. i limp the bike home (it wont tick over) and got a wet sponge and put it on my headers..

3 and 4 make the sponge sizzle and they evaporate the water quickly. cylinder 1 and 2 just evapourate the water but without the sizzle telling me theyre not as hot as the other cylinders..

what can i do to resolve this problem?

Post by **Delboy** » Sun May 29, 2011 5:12 pm

Are the HT leads on tight? give em a push on the spark plug end (looking for cheap fix 1st)

DK-Tandy · Post by **DK-Tandy** » Sun May 29, 2011 6:13 pm

i pulled all HT's off and refitted and its working now :D

Post by **Delboy** » Sun May 29, 2011 7:10 pm

Nice one Dan

DK-Tandy · Post by **DK-Tandy** » Sun May 29, 2011 11:10 pm

with an I4, when on tickover should certain headers get hot?? i found its running on 4 cylinders but only 1 and 4 make a wet sponge sizzle, the middle 2 dont? is that right for tick over??

Post by **tanuki** » Mon May 30, 2011 10:54 am

No they should all be the same temperature.

DK-Tandy · Post by **DK-Tandy** » Mon May 30, 2011 11:05 am

what would cause the inner 2 to not run as hot as the others??

Post by **Wozza** » Mon May 30, 2011 11:25 am

Either a weak spark or fuelling is off. The latter could be a partly blocked jet, incorrect float heights, or simply the carbs need balancing. I would check the sparks, then balance the carbs if they've not been done for a while.

DK-Tandy · Post by **DK-Tandy** » Mon May 30, 2011 11:29 am

ive tried many different tools to remove sparks, i cant find a tool that will go all the way down and i dont exactly have the money to throw around to afford one..

the other day when it was running on 3 cylinders all the working ones were at same temp, but since all 4 work, 2 dont

is it bad to use the bike in its current state?

DK-Tandy · Post by **DK-Tandy** » Mon May 30, 2011 12:38 pm

will adjusting the tick over screw on the side affect the heating of my headers..?

not running right on all 4..

not running right on all 4..

Re: not running right on all 4..

Re: not running right on all 4..

Re: not running right on all 4..

Re: not running right on all 4..

Re: not running right on all 4..

Re: not running right on all 4..

Re: not running right on all 4..

Re: not running right on all 4..

Re: not running right on all 4..