Advice needed please!

Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
wullvfr
Site Supporter
Site Supporter
Posts: 1027
Joined: Wed Apr 30, 2008 8:40 pm
Bike owned: zx9r c1
Location: killin,scotland
Re: Advice needed please!

Post by wullvfr »

is there any signs of it running very rich?


out of curiosity when was the valve clearances last checked/done?




william
please,god,....give me the chance to prove that winning the lottery won't spoil me!!!
User avatar
CMSMJ1
Moderators
Moderators
Posts: 7161
Joined: Thu May 01, 2008 9:42 am
Bike owned: NC30-No9
Location: Chesterfield, United Kingdom
Re: Advice needed please!

Post by CMSMJ1 »

This is still not running as far as I know.. doesn't run overly rich but it is a strange beast and needs a kicking!!
IMPERATOR REX ANGLORUM

The V4 is the law..

NC30 - No9 - my old mate
Evilchicken0
Site Supporter
Site Supporter
Posts: 5374
Joined: Tue Apr 29, 2008 8:59 pm
Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
Location: Lundin Taan
Re: Advice needed please!

Post by Evilchicken0 »

Lets stone it ... :P
User avatar
CMSMJ1
Moderators
Moderators
Posts: 7161
Joined: Thu May 01, 2008 9:42 am
Bike owned: NC30-No9
Location: Chesterfield, United Kingdom
Re: Advice needed please!

Post by CMSMJ1 »

Zombie thread

So, this motor is now living with me and wants to get sorted, I am going to take the carbs off and clean them up nicely.

I'll see if I can get Craig to do the valve clearances too as they'll probably want a look at.

The bike starts and runs lovely. Just when under full throttle it starts to break down. It does not rev out and makes all sorts of noises.

So....any takers on fuelling or ignition?
IMPERATOR REX ANGLORUM

The V4 is the law..

NC30 - No9 - my old mate
User avatar
laminator
NWAA Supporter
NWAA Supporter
Posts: 220
Joined: Wed Jan 26, 2011 7:51 pm
Bike owned: 2tk,NC30, YB7
Location: Midlands
Re: Advice needed please!

Post by laminator »

Is the air filter OK?

I've just helped strip and clean some carbs, on a suzuki, that would not like reving over 8k (when it did it smoked). It turned out to be the filter. The carbs had been on/off several times before he tried the filter.

Just a thought.
User avatar
CMSMJ1
Moderators
Moderators
Posts: 7161
Joined: Thu May 01, 2008 9:42 am
Bike owned: NC30-No9
Location: Chesterfield, United Kingdom
Re: Advice needed please!

Post by CMSMJ1 »

I'll check it out. Sure he has fucked about with it in the past too.... standard bits for the win!
IMPERATOR REX ANGLORUM

The V4 is the law..

NC30 - No9 - my old mate
Evilchicken0
Site Supporter
Site Supporter
Posts: 5374
Joined: Tue Apr 29, 2008 8:59 pm
Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
Location: Lundin Taan
Re: Advice needed please!

Post by Evilchicken0 »

Use some known working carbs on it first - hopefully that will give a place to start.
Check the EXUP is opening and closing - or disconnect it just to try.

Have a look at the side stand return spring and cut out switch - bridge the switch.
Has somebody butcherred the speedo restrictor ... the symptoms are almost like the CDI's cutting the sparks, maybe somebody tried to cut the disc in the speedo ?
User avatar
Hogdigerdy Dog
Site Supporter
Site Supporter
Posts: 545
Joined: Mon Sep 14, 2009 6:34 pm
Bike owned: FZR400RR 3TJ, ZX9R fighter
Location: Dorsetshire
Re: Advice needed please!

Post by Hogdigerdy Dog »

have you checked the exup valve,
if it's stuck shut or not opening fully then it's a bit like putting your hand over the end can at high rev's it'll fart, pop, bang and make allsorts of strange noises, and it's fairly easy to eliminate
http://www.cartestsoftware.com/fz1/exupmaintenance.html

i doubt both coils have gone down at once (could do, but unlikely) so swap em over and see if it makes a difference

valve clearances is another job worth doing and could be your hot starting/high rev running problem

and as every one has said these TJs are a bit fussy when it comes to airbox and carbs, i'd check to make sure you have standard jets in the carbs and a decent air filter

Image

have fun ;)
Tomahawk
Settled in member
Posts: 78
Joined: Tue Jun 15, 2010 5:34 pm
Re: Advice needed please!

Post by Tomahawk »

Im having the same problems but with idle. Mine gets stuck between 1-2 thousand revs and you can give it full gas and it wont even move or stall!. My mains jets are 100 and 50 i have no idea if thats right. Luckily i managed to get myself a second hand set of carbs so hopefully that will cure my problem.

Post Reply