RVF unstable work >6000 RPM

Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Post Reply
Eniac
Settled in member
Posts: 6
Joined: Sun May 22, 2011 1:16 pm

RVF unstable work >6000 RPM

Post by Eniac » Tue May 24, 2011 12:24 pm

Until recently, my bike worked like a clock. Recently i had to ride over rough terrain, with some sand on the road. Total mileage was 8-10 km. I got to the garage without any problems, but the next day when i ride to work motorcycle after 6rpm + loses power and starts to stutter.
When i return to the garage, i cleaned the air filter (it was decent sandy), carbs are completely washed and blew with compressed air, rubber membranes sprayed for softness with silicone, tank was cleaned also(HRC mod on fuel tap)etc. I have been assured that a problem with fuel delivery system, but anything from this hasn't brought results. :whistle:
My numerous rides have shown interesting feature. After the motorcycle doesn't go about 3-5 hours, i can ride normally in a short distance(5-10 km).
Can you advise where to look further?. :arrow:
Top
amorti
Regular Member
Posts: 957
Joined: Sun May 18, 2008 4:51 pm
Bike owned: CB-1, MSX125
Location: Gibraltar

Re: RVF unstable work >6000 RPM

Post by amorti » Tue May 24, 2011 1:51 pm

Hi Eniac,
is the fault really definitely related to 6k rpm?
If so, I would suggest the speed restrictor has somehow failed.
Top
Eniac
Settled in member
Posts: 6
Joined: Sun May 22, 2011 1:16 pm

Re: RVF unstable work >6000 RPM

Post by Eniac » Tue May 24, 2011 2:29 pm

The error starts in a range 5-7k RPM and to a red line. Still it is necessary to mention that my instrument panel was derestricted...
Top
User avatar
Drunkn Munky
Site Supporter
Site Supporter
Posts: 6313
Joined: Thu May 01, 2008 9:37 am
Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
Location: Kent

Re: RVF unstable work >6000 RPM

Post by Drunkn Munky » Tue May 24, 2011 5:12 pm

Have you unplpuged your speedo?

Theres a rev limit wire that comes from your cdi, this needs to be connected to a +12v source if its been disconnected/removed in any way, ie when you disconnect the speedo. Its a limp home mode that cuts 2 cylinders at around 5.5k to 6k.
Top
amorti
Regular Member
Posts: 957
Joined: Sun May 18, 2008 4:51 pm
Bike owned: CB-1, MSX125
Location: Gibraltar

Re: RVF unstable work >6000 RPM

Post by amorti » Tue May 24, 2011 5:19 pm

Eniac wrote:The error starts in a range 5-7k RPM and to a red line. Still it is necessary to mention that my instrument panel was derestricted...
I suggest the join there has failed. After a little time running it heats up, goes high resistance and then cuts the limiter in because the bike thinks it's doing 180kmh
Top
Eniac
Settled in member
Posts: 6
Joined: Sun May 22, 2011 1:16 pm

Re: RVF unstable work >6000 RPM

Post by Eniac » Wed May 25, 2011 9:37 am

I run to check all my wiring loom... :idea:
:rocks:
Top
Eniac
Settled in member
Posts: 6
Joined: Sun May 22, 2011 1:16 pm

Re: RVF unstable work >6000 RPM

Post by Eniac » Tue May 31, 2011 5:14 pm

Drunkn Munky wrote:Have you unplpuged your speedo?

Theres a rev limit wire that comes from your cdi, this needs to be connected to a +12v source if its been disconnected/removed in any way, ie when you disconnect the speedo. Its a limp home mode that cuts 2 cylinders at around 5.5k to 6k.
:rocks:
Thanks a lot, it have solved my problem
Top
Post Reply

Return to “Honda - Workshop”