Scott's NC30 Track Bike Build

This section is reserved for members on the SITE SUPPORTERS group only. Each supporter can post pics of their bikes for all to view. Standard members can read and reply, but the post author has full control over his thread and can edit, delete & lock at will
User avatar
TZcRank
NWAA Supporter
NWAA Supporter
Reactions:
Posts: 46
Joined: Wed Apr 18, 2018 5:54 am
Location: JHB - South Africa
Re: Scott's NC30 Track Bike Build

Post by TZcRank » Sat Jan 12, 2019 8:24 pm

Any idea why the handle bars are different weights ? The left is a fair bit heavier that the right.

User avatar
TZcRank
NWAA Supporter
NWAA Supporter
Reactions:
Posts: 46
Joined: Wed Apr 18, 2018 5:54 am
Location: JHB - South Africa
Re: Scott's NC30 Track Bike Build

Post by TZcRank » Sun Jan 13, 2019 4:00 pm

Ok I'll just keep chatting to myself here lol. If the left being heavier than the right compensates for anything I won't benefit from it anyway as all three right side bars are bent on the bikes I have. So two left's with a hole for the throttle locater drilled will have to do for now. A set of turned ali bars will replace them in the near future.

User avatar
TZcRank
NWAA Supporter
NWAA Supporter
Reactions:
Posts: 46
Joined: Wed Apr 18, 2018 5:54 am
Location: JHB - South Africa
Re: Scott's NC30 Track Bike Build

Post by TZcRank » Mon Jan 14, 2019 7:37 am

Small update from the weekend:
Got the front rim sprayed and decided to clean up the front discs.
Used paint stripper to get the old black paint off. Quick sand and masked off ready for Satin black paint.
Got new wheel bearings and installed them too.

Image
Image
Image
Image
Image

User avatar
TZcRank
NWAA Supporter
NWAA Supporter
Reactions:
Posts: 46
Joined: Wed Apr 18, 2018 5:54 am
Location: JHB - South Africa
Re: Scott's NC30 Track Bike Build

Post by TZcRank » Mon Jan 14, 2019 7:47 am

I couldn't understand why I had to fight with the top triple clamp to install it and the axle was also near impossible to get through the forks!
After a good think it occurred to me that something may be bent. I did find one bent fork tube in the set of forks that came off this particular bike.
A few measurements and a really good look at them I realised that the right hand side of the bottom triple clamp is twisted down and backwards!!
Thought it was odd that the front tyre had more wear on one side......must have been an interesting ride for the previous owner.

You can clearly see the twist in this pic I posted before:
Image

CB1pod70
NWAA Supporter
NWAA Supporter
Reactions:
Posts: 369
Joined: Thu Apr 09, 2015 1:55 pm
Location: Gravesend
Re: Scott's NC30 Track Bike Build

Post by CB1pod70 » Mon Jan 14, 2019 1:24 pm

TZcRank wrote:
Fri Jan 11, 2019 10:11 am
I have a RVF 17 inch rear for the bike.
Has anybody run a 160 tyre (Pirelli Supercorsa) and did it affect handling / feel on the bike.
I know 150 is recommended but it will be far cheaper to get a 120 / 160 combo.
All the Guys I race with use the 160 / 120 supercorsa combo on their bikes (pretty much the tyre of choice for all 400's) so you will be fine. The biggest problem is getting hold of 17" RVF rears these days...

User avatar
TZcRank
NWAA Supporter
NWAA Supporter
Reactions:
Posts: 46
Joined: Wed Apr 18, 2018 5:54 am
Location: JHB - South Africa
Re: Scott's NC30 Track Bike Build

Post by TZcRank » Tue Jan 15, 2019 7:01 am

Thanks CB1pod70. I will be using a lightly scrubbed BT090 150 rear that I had in my stash and a new 120 front for the first event.
Would have preferred the Pirelli's but it came down to cost and the serious lack of budget this month.

User avatar
TZcRank
NWAA Supporter
NWAA Supporter
Reactions:
Posts: 46
Joined: Wed Apr 18, 2018 5:54 am
Location: JHB - South Africa
Re: Scott's NC30 Track Bike Build

Post by TZcRank » Wed Jan 16, 2019 10:14 am

Small update again. I turned some new ali wheel spacers, every gram helps lol.

Image

Also found some factory brake pads in one set of calipers, that bike had just over 20k kilometers on the clock!!!

Image

Also had problems with wheel alignment, couldn't get equal gaps between the forks and front wheel.
Eventually figured out that the axle is bent, by chance I rotated it and immediately saw the gaps changing with the wheel moving sideways.
So this bike had a bent fork stanchion, bent lower triple clamp and now the axle/spindle!


Post Reply

Return to “Members Bikes & Rides”