hunter wrote:Kala is this any help,The only thing i didn't measure was the dia.

Perfect! Thank you

Glad to be of help,
And thanks for the Karma.

Cool. Nice one. Put me down for a 'set of 3' for the NC30.

Plus one for the rear hub bolt when you get round to getting them made.
I shall start a new list

Hub adjuster bolt
1. Timon
2. ...

Timon wrote:Plus one for the rear hub bolt when you get round to getting them made.
I shall start a new list

Hub adjuster bolt
1. Timon
2. ...

No need for lists, they are being made as I type and they will be sold on a first come, first served basis through my website, using the checkout procedure to keep it separate from the forum and let me keep track of who wants what. PMs and promises to buy stuff are ok for small amounts, but I'm going to have at least 125 (25 each of the hub nut, both top yoke nuts, wheel nut and the adjuster bolt) pieces to keep an eye on so these are going to be available to anyone who wants one and can pay.

Kayla850 wrote:

Timon wrote:Plus one for the rear hub bolt when you get round to getting them made.
I shall start a new list

Hub adjuster bolt
1. Timon
2. ...

No need for lists, they are being made as I type and they will be sold on a first come, first served basis through my website, using the checkout procedure to keep it separate from forum and let me keep track of who wants what. PMs and promises to buy stuff are ok for small amounts, but I'm going to have at least 125 (25 each of the hub nut, both top yoke nuts, wheel nut and the adjuster bolt) pieces to keep an eye on so these are going to be available to anyone who wants one and can pay.

Kayla you rock chick

Thanks for sorting this out,

are you going about do the hub adjuster bolt? ill deffo have one of them too if you are?

porndoguk wrote: Kayla you rock chick

Thanks for sorting this out,

are you going about do the hub adjuster bolt? ill deffo have one of them too if you are?

Thanks Rick, but to be honest it was you pushing it and not taking no for an answer that did it! The adjuster bolts are drilled head flange bolts and are in with the next lot of stuff with the NC35 top yoke nuts. I couldn't afford to order everything in one go, so will be sorting them out towards the middle of the month. The parts will be available at slightly staggered times but once they start to sell (ie I start to recoup some of what I've paid out) I can order more stuff.

Kayla850 wrote:No need for lists, they are being made as I type and they will be sold on a first come, first served basis through my website

I'm so going to forget about this and end up missing out.

Rick remind me please

Timon wrote:

Kayla850 wrote:No need for lists, they are being made as I type and they will be sold on a first come, first served basis through my website

I'm so going to forget about this and end up missing out.

Rick remind me please

I'll put a post up in the Trader's section when they're ready, just to avoid spamming the bikes bit with trade posts, but I'm pretty sure they won't sell out before you get round to buying one.

Kayla850 wrote:

Timon wrote:

Kayla850 wrote:No need for lists, they are being made as I type and they will be sold on a first come, first served basis through my website

I'm so going to forget about this and end up missing out.

Rick remind me please

I'll put a post up in the Trader's section when they're ready, just to avoid spamming the bikes bit with trade posts, but I'm pretty sure they won't sell out before you get round to buying one.

Kayla you arnt spamming chick your helping us get the bit we need, without you we would struggle, we occasionally have organised chaotic posts about bulk and group buys this years most sucessful was NC30 MPH speedo Redials at £26 each and i had to pay out £500+ to get them made up front :s