• CRM's RVF400 project - Project " skinned knuckles*"

Posted: **Fri Sep 10, 2010 7:57 pm**

Very kind offer, however you may note some already fitted to this said RVF.
anyway i will raise your red bar ends with a faded pink rear wheel spacer !
nah - beat that

Posted: **Fri Sep 10, 2010 8:01 pm**

I have clear handlgrips with silver VFR inlayed into them, truly beautiful only found on the rarest of NC30's!!

Beat that!!

Kris

Posted: **Fri Sep 10, 2010 8:13 pm**

I have an anodized pink m/c bracket. And no I'm not joking.

Posted: **Fri Sep 10, 2010 8:20 pm**

i wanna see this stuff. see new post in general. c'mon i want pics or they dont exist !

Posted: **Fri Sep 10, 2010 8:23 pm**

Time to find the bucket 'o' tat.

Posted: **Mon Sep 13, 2010 8:28 pm**

CRM wrote:...

Tearing off all the panels, and rubbish i am greeted with signs of a aerosol "touch up" on the subframe, with a bit of overspray on anything else in the vicinity. however thats nothing. what did greet me was this. a HRC CDI which was nice. peeled the sticker back and sure enough a pukka HRC item.
DSCN0652.JPG
...

Paul, about that sticker on the HRC cdi, this is what I found on my project bike

Posted: **Mon Oct 04, 2010 8:48 am**

Well not alot to report really, its getting cold out there, lights fading so time to work on it is becoming limited so i need to get my arse into gear.
as you can see its got no rear, this week i need to remove the front wheel and get these off to tony, so hopefully in 2 weeks it will have a pair of fresh white wheels fitted and it can be moved around.

rear shock was actually good, a tad more preload (for my bulk) and a clean and refitted with some fresh grease on the linkages and rollers.

changed the rear manifold and fitted the lovely laser exhaust system, just need some springs to hold it together.

carbs cleaned, and jetted to suit, new carb rubbers, clean engine all degreased and as clean as a scabby old cast RVF engine can get.

Swingarm still needs more work but its cleaning slowly.

So as you can see, until its clean under the skin and adjusted and greased, there is not much point putting its clothes back on.

Still need a new nosecone and a clear or light tint screen so if anyone has one

DSCN0667.JPG

Posted: **Mon Oct 04, 2010 10:55 am**

That Laser system looks lovely Paul, Is it a Laser end can too?

Nice find that!!

Kris

Posted: **Mon Oct 04, 2010 11:00 am**

Full system Kris, got it from Simon (EDG65) and a load of other parts to get me started building it backup. i was going to put a standard system on it, but thought "what the hell"

Posted: **Mon Oct 04, 2010 11:05 am**

Ahh you too have encountered Aladdins cave AKA Eg65 garage haha! Really nice mate looks good!!

Kris

CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"

Re: CRM's RVF400 project - Project " skinned knuckles*"