Nice Rick, liking the heel guard, looking trick

not near the big reveal yet however this was taken on saturday just gone,

[img]http://i107.photobucket.com/albums/m302 ... f3c927.jpg[/img]

[img]http://i107.photobucket.com/albums/m302 ... a1ae05.jpg[/img][/quote]


Fantastic, thanks Rick - looks great. Very nice bike after all that work you've put in...

Is that the HRC Gold?

Cheers,

Ben.

Ben_OB1 wrote:
Fantastic, thanks Rick - looks great. Very nice bike after all that work you've put in...

Is that the HRC Gold?

Cheers,

Ben.

well close, it was one of three powder choices at the coaters i went for "GOLD 76"

i hope he has some left as i want a 17" RVF wheel doing when i get one other wise ill have to get a front and get them painted HRC. well see a little further down the line, ill await for the tyres to get worn etc.

good job, just took the letters to say VFR and put others a little more smaller


some work I made in my nc30:
http://400cm3.hostei.com/index.php?board=14.0

7pires wrote:good job, just took the letters to say VFR and put others a little more smaller


some work I made in my nc30:
http://400cm3.hostei.com/index.php?board=14.0

what do you mean pires?

also that link what should i look at i cant speak/read (Portuguise)

nice work Porndoguk, tanks for share, in my site can see the pictures

Just reread your whole thread, nice work mate.
I want your rear caliper.
Whats your plan for the other set of bodywork?

Timon wrote:Just reread your whole thread, nice work mate.
I want your rear caliper.
Whats your plan for the other set of bodywork?

cheers Tim,
if i had time i would refurb them for people but i just dont have the spare time at the moment,

well im in a bit of a rut at the min, things in the family have changed so the bike is on the back burner cosmetically, it will be just a good clean & OIL change this coming winter.

sticking with the silver fiberglass ones for now, the bike is mechanically sound, and cosmetics are the least important as a priority, im going to brighten the bike up as it is buy chucking a few choice sticker/decals on,
HRC on the seat panel, Bridgestone, NGK, RK on the belly pan, im fed up of seeing BLACK & SILVER need some red chucked in there, so the bridgestone logo's RK NGK and HRC's should break it up.

the originals will be fully preped, painted, any repairs made that are needed, insulated on the rear, i have a stupid ammount of pannels i have 3 nosecones!

BUT

i want Silohuete so if one becomes available within the next few months ill be jumping on it!

i need to get some more pics and update,

recently fitted:

Sprint Damper (Reverse Mount) £51 ebay bargain
MPH Speedo Facia
FULL tyga stainless system, with 440mm carbon can (£640)
Blue Samco Hoses & Jubilees (£100)
Lower Tank Rubber

Next Weeks Work

one Samco hose under carbs from thermostat to rear block
Re Fill and bleed cooling system
Blue Silicon Hoses for petrol over flow, air box lid and catch tank,
Catch Tank next to RHS/OS head light
New #35 Pilot Jets to go it,
NC24 Slides to be fitted
1 washer from each needle to be removed
15T Sprocket to fit in place of the 14T
loosen/retention chain

Things to do :
Refurb original later model NC30 Rear shock with RS250 Remote Resovoir,
front and rear heads to be swaped, (Probally gonna just get another engine to overhaul on the bench then swap when done)
PLASTICS/Bodywork (Silohuette & RC45 Solo Seat Unit)
17" Rear Wheel

swaped the switch over for a newer fresher one with no fading and all writting there, also white gloss humbrol on the horn switch

Am I thinking of someone else or is that the switchgear I gave you?

iDemonix wrote:

swaped the switch over for a newer fresher one with no fading and all writting there, also white gloss humbrol on the horn switch

Am I thinking of someone else or is that the switchgear I gave you?

this was another as yours didnt have the High, Low, Off marking on the case,

your case was fitted for a short while about 6months it graced its unfaded presence on my bike :)