NC30 - wiring loom

Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Post Reply
User avatar
lukemillar
Site Supporter
Site Supporter
Posts: 690
Joined: Thu Aug 26, 2010 11:43 pm
Bike owned: '89 NC30 Racebike #24
Location: Wellington, New Zealand

NC30 - wiring loom

Post by lukemillar » Wed Aug 20, 2014 3:31 am

Rather than cut down a stock loom to make a race loom, I figure it would be far nicer/easier to just make one from scratch. Thing is, I really want to stick to the wiring diagram colours so that it will be easy to refer back to in the future. All the local places just sell solid colour wires, so I'm looking offshore.

Does anyone has a good source (online) of electrical components and wire that is likely to stock all/most the various colour combinations of wire that you would find on an NC30 loom?

Thanks
Luke
Top
User avatar
28hodge
Site Supporter
Site Supporter
Posts: 650
Joined: Tue May 17, 2011 4:26 pm
Bike owned: nc30 (track) Yam YZ250 (MX)2st
Location: Kendal, Cumbria, Northwest

Re: NC30 - wiring loom

Post by 28hodge » Wed Aug 20, 2014 8:32 am

I used these guys Luke when I built my race loom, think they will be able to keep you very close to the original honda colours.

http://kojaycat.co.uk/
Top
binners
Settled in member
Posts: 14
Joined: Thu Jul 31, 2014 1:21 pm

Re: NC30 - wiring loom

Post by binners » Wed Aug 20, 2014 9:43 am

I was just thinking about this today! My only problem with this is I'm colour blind! I think that would make it a challenge!
Top
User avatar
lukemillar
Site Supporter
Site Supporter
Posts: 690
Joined: Thu Aug 26, 2010 11:43 pm
Bike owned: '89 NC30 Racebike #24
Location: Wellington, New Zealand

Re: NC30 - wiring loom

Post by lukemillar » Sun Oct 12, 2014 12:07 am

Argh - never replied!

Thanks Kurt, that site is epic!
Top
binners
Settled in member
Posts: 14
Joined: Thu Jul 31, 2014 1:21 pm

Re: NC30 - wiring loom

Post by binners » Sun Oct 12, 2014 12:46 am

There is alot of stuff on that site! I'm just about to order some stuff myself. Are you replacing the ICM plug? If so I found a place in the states that has it!
Top
jasonmac87
Settled in member
Posts: 6
Joined: Mon Jun 24, 2013 9:34 pm

Re: NC30 - wiring loom

Post by jasonmac87 » Thu Oct 16, 2014 7:26 pm

binners wrote:There is alot of stuff on that site! I'm just about to order some stuff myself. Are you replacing the ICM plug? If so I found a place in the states that has it!
I'm going to make a hrc replica race look myself, where did you come across the icm plug?
Top
binners
Settled in member
Posts: 14
Joined: Thu Jul 31, 2014 1:21 pm

Re: NC30 - wiring loom

Post by binners » Fri Oct 17, 2014 1:47 pm

I found it at a place called Cycle Terminal. If you search through his website you'll find it!
Top
User avatar
lukemillar
Site Supporter
Site Supporter
Posts: 690
Joined: Thu Aug 26, 2010 11:43 pm
Bike owned: '89 NC30 Racebike #24
Location: Wellington, New Zealand

Re: NC30 - wiring loom

Post by lukemillar » Fri Oct 17, 2014 9:55 pm

Ha - I found that website a week ago look for good quality crimpers. That site is going to cost me!
Top
magg
Senior Member
Posts: 1913
Joined: Mon Sep 20, 2010 11:55 pm
Bike owned: VFR400
Location: Blue Mountain NSW Australia

Re: NC30 - wiring loom

Post by magg » Fri Oct 17, 2014 11:17 pm

IMHO save your money on expensive crimpt tools and just solder the connections.
Top
binners
Settled in member
Posts: 14
Joined: Thu Jul 31, 2014 1:21 pm

Re: NC30 - wiring loom

Post by binners » Thu Oct 23, 2014 6:55 am

What makes you say that? I know it's a bit of an outlay, but I would have thought the crimpers would make for a better job.
Top
Post Reply

Return to “Honda - Workshop”