Project NC29 spangly bastard!
-
cbr400rrbernard
- Settled in member
- Posts: 4
- Joined: Sun Apr 17, 2011 4:53 pm
Re: Project NC29 spangly bastard!
nowt fancy mate fairly standard dyno filter can an some head work
-
cbr400rrbernard
- Settled in member
- Posts: 4
- Joined: Sun Apr 17, 2011 4:53 pm
Re: Project NC29 spangly bastard!
have you any spares ?
-
tanuki
- Site Supporter
- Posts: 1571
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
Re: Project NC29 spangly bastard!
most of an engine....some coolant pipes, a couple of yokes.
Thats about it.....will soon have a powdercoated frame.
Thats about it.....will soon have a powdercoated frame.
-
tanuki
- Site Supporter
- Posts: 1571
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
Re: Project NC29 spangly bastard!
Bit more done on the motah....
Few more bits and bobs to bolt in and we should be able to get the casings back together, unfortunately other than bolting on stuff like the thermostat and starter that's where it will end for the engine.
Few more bits and bobs to bolt in and we should be able to get the casings back together, unfortunately other than bolting on stuff like the thermostat and starter that's where it will end for the engine.
-
cajun
- Familiar Member
- Posts: 264
- Joined: Sat Jun 13, 2009 4:06 am
- Bike owned: MC22, NC29,NC35, 2 FZR400's
- Location: New Orleans, LA USA
Re: Project NC29 spangly bastard!
Cool keep me updated. Did you start a group buy thread?
-
tanuki
- Site Supporter
- Posts: 1571
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
Re: Project NC29 spangly bastard!
Will do it today in CBR general.
-
cbr400rrbernard
- Settled in member
- Posts: 4
- Joined: Sun Apr 17, 2011 4:53 pm
Re: Project NC29 spangly bastard!
any updates ?
-
tanuki
- Site Supporter
- Posts: 1571
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
Re: Project NC29 spangly bastard!
not really.
The main bodywork has been fitted so I can see where I need to trim it etc but dont want to do anymore until the seat unit is fitted, Subframes are being made as I type this and I'm waiting for some more crank shells from Honda as I stupidly only ordered 1/2 a set.
The main bodywork has been fitted so I can see where I need to trim it etc but dont want to do anymore until the seat unit is fitted, Subframes are being made as I type this and I'm waiting for some more crank shells from Honda as I stupidly only ordered 1/2 a set.
-
tanuki
- Site Supporter
- Posts: 1571
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
Re: Project NC29 spangly bastard!
Credit card has just taken a beating....
SPLOINK!!
SPLOINK!!
-
justmartyn
- Site Supporter
- Posts: 198
- Joined: Sun May 04, 2008 4:57 am
- Bike owned: Only 2 left.....
- Location: Northern Ireland and the Middle East
Re: Project NC29 spangly bastard!
Worth every penny.