Project NC29...Konica Minolta rep
-
- Site Supporter
- Reactions:
- Posts: 108
- Joined: Sun Jan 10, 2010 9:07 pm
- Bike owned: CBR400 NC29
- Location: Lincoln
Re: Project NC29...Konica Minolta rep
Ok.....first bit of bling bought this week.
My standard rearsets were mashed to be fair.....right set needed a new brake lever, left set were bent forwards where the footpeg joins the hanger itself.
So after pricing up the options, i couldnt believe my luck when i found the below on ebay.
I made the guy an offer of £60 for the pair, and the deal was done!
My standard rearsets were mashed to be fair.....right set needed a new brake lever, left set were bent forwards where the footpeg joins the hanger itself.
So after pricing up the options, i couldnt believe my luck when i found the below on ebay.
I made the guy an offer of £60 for the pair, and the deal was done!
- Drunkn Munky
- Site Supporter
- Reactions:
- Posts: 6313
- Joined: Thu May 01, 2008 9:37 am
- Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
- Location: Kent
Re: Project NC29...Konica Minolta rep
Beet for £60, bargin
- w00dzy
- Site Supporter
- Reactions:
- Posts: 514
- Joined: Sun Oct 12, 2008 10:44 pm
- Bike owned: Aprilia RSVR Mille
- Location: Hampshire
Re: Project NC29...Konica Minolta rep
Great rearsets, have a set myself..
-
- Site Supporter
- Reactions:
- Posts: 108
- Joined: Sun Jan 10, 2010 9:07 pm
- Bike owned: CBR400 NC29
- Location: Lincoln
Re: Project NC29...Konica Minolta rep
Offering them upto the bike, i notice they are a good maybe 2" higher and further back than the oem units
-
- Site Supporter
- Reactions:
- Posts: 108
- Joined: Sun Jan 10, 2010 9:07 pm
- Bike owned: CBR400 NC29
- Location: Lincoln
Re: Project NC29...Konica Minolta rep
Hello guys......long time no post ....i hope everyone is well.
From the last time i posted until now, the project has been at a standstill due to lack of motivation
To be fair, my trackcar was starting to take over my life, so i sold it and thought i must crack on with this
Just uploading some pics to show progress so far.........its still in the garage in bits
From the last time i posted until now, the project has been at a standstill due to lack of motivation
To be fair, my trackcar was starting to take over my life, so i sold it and thought i must crack on with this
Just uploading some pics to show progress so far.........its still in the garage in bits
-
- Site Supporter
- Reactions:
- Posts: 108
- Joined: Sun Jan 10, 2010 9:07 pm
- Bike owned: CBR400 NC29
- Location: Lincoln
Re: Project NC29...Konica Minolta rep
Ok, here we go..............
I had a problem with the bike being on the front paddock stand, the forks moved/sank lower on one side as it took the weight.....therefore, i couldnt actually get the front wheel back in as the spindle wouldnt line up
The car jack and a piece of wood came in handy......surprisingly sturdy aswell, and, i can get to the forks for painting.
I had a problem with the bike being on the front paddock stand, the forks moved/sank lower on one side as it took the weight.....therefore, i couldnt actually get the front wheel back in as the spindle wouldnt line up
The car jack and a piece of wood came in handy......surprisingly sturdy aswell, and, i can get to the forks for painting.
-
- Site Supporter
- Reactions:
- Posts: 108
- Joined: Sun Jan 10, 2010 9:07 pm
- Bike owned: CBR400 NC29
- Location: Lincoln
Re: Project NC29...Konica Minolta rep
Onto the bits done so far, doesnt look a lot, but the cleaning / sanding / masking / primering / finishing etc......takes ages!
Been doing a bit a day to keep going.
Fairing support was too far gone really, lots of surface rust etc....so i just rubbed it down and hammerited black
Exhaust was rubbed down and prepped.....VHT paint applied......wheel brace came in hand to mount the exhaust too in the ground
Calipers cleaned down and painted "ford tibetan gold"
Same colour for the brake disc inners
Forks now painted....i couldnt figure out how to get the white plastic mudguard mounts off....so painted them aswell
Radiator end tanks prepped and painted aswell.
Exhaust hanger painted.
The air ducts were cracked in several places, so i had to fill the inside with fibreglass and smooth over the top etc, this took the longest out of everything done so far.....came out nice though.
Been doing a bit a day to keep going.
Fairing support was too far gone really, lots of surface rust etc....so i just rubbed it down and hammerited black
Exhaust was rubbed down and prepped.....VHT paint applied......wheel brace came in hand to mount the exhaust too in the ground
Calipers cleaned down and painted "ford tibetan gold"
Same colour for the brake disc inners
Forks now painted....i couldnt figure out how to get the white plastic mudguard mounts off....so painted them aswell
Radiator end tanks prepped and painted aswell.
Exhaust hanger painted.
The air ducts were cracked in several places, so i had to fill the inside with fibreglass and smooth over the top etc, this took the longest out of everything done so far.....came out nice though.
-
- Site Supporter
- Reactions:
- Posts: 108
- Joined: Sun Jan 10, 2010 9:07 pm
- Bike owned: CBR400 NC29
- Location: Lincoln
Re: Project NC29...Konica Minolta rep
Waiting for oil filter / engine case gaskets to turn up before i can attack the engine case covers.
Im working from front to back, so before the front end goes on, i can tidy up all the bolts and the engine where they have "furred up".
I've decided against painting the frame / swingarm black, as i know i would be majorly pi55sed if it didnt come out right.
So, just lots of autosol to clean all the bare alloy up.
Its moving nicely now.
Im working from front to back, so before the front end goes on, i can tidy up all the bolts and the engine where they have "furred up".
I've decided against painting the frame / swingarm black, as i know i would be majorly pi55sed if it didnt come out right.
So, just lots of autosol to clean all the bare alloy up.
Its moving nicely now.
-
- Site Supporter
- Reactions:
- Posts: 750
- Joined: Tue Apr 29, 2008 9:37 pm
- Bike owned: NC29 CBR600F
- Location: Lancashire
Re: Project NC29...Konica Minolta rep
Love the wheel brace approach.
-
- Site Supporter
- Reactions:
- Posts: 108
- Joined: Sun Jan 10, 2010 9:07 pm
- Bike owned: CBR400 NC29
- Location: Lincoln
Re: Project NC29...Konica Minolta rep
A moment of genius i am immensly proud of