Page 33 of 37

Re: RVF Endurance AM-PM Replica build

Posted: Mon Aug 08, 2011 12:14 pm
by Drunkn Munky
I know its a piss take, clare sends most of my stuff through her work which is all garantee'd next day and they charge well over the top for the service, hardly any of the stuff i send gets there next day. Courier companys are on the rob big time.

Re: RVF Endurance AM-PM Replica build

Posted: Wed Aug 10, 2011 10:36 pm
by Drunkn Munky
Took it out for a ride today, low down the fueling is intermitantly crap with the occasional stutter in the midrange, i still need to work on that carb me thinks. WOT is great and no issues there at all but i think i may drop back down to standard gearing, its currently +2 on the rear and hitting the limiter in 6th is far to easy.

Pic from today
Image
And NC30 carbs off, HRC tray fitted ready for the open RVF carbs that should be arriving soon
Image
Image

Re: RVF Endurance AM-PM Replica build

Posted: Wed Aug 10, 2011 10:54 pm
by BillingCBR
Looks fantastic mate, can't wait to see it properly finished, it'll run as good as it looks :up: How does the HRC air tray attach? Just thinking there's no bolt points, so it looks like it'll rattle around :S

Re: RVF Endurance AM-PM Replica build

Posted: Wed Aug 10, 2011 10:58 pm
by Drunkn Munky
No chance of it rattling around, the scoop is cable tied to the top of the rad and the carbs pretty much sit down on the tray.

Re: RVF Endurance AM-PM Replica build

Posted: Thu Aug 11, 2011 6:17 am
by Martin
:grin:

Re: RVF Endurance AM-PM Replica build

Posted: Thu Aug 11, 2011 10:26 am
by Drunkn Munky
Eureka ka ka ka ka ka ka :grin: open RVF carbs arrived this morning (thanks james) fitted them and once she fired i could just tell by the note of the exhausts that things were right. there was no idle adjustment on the carbs but even cold it will idle at just over 1k, anything below 1500 rpm on the old carbs would stall even when warm.

I still cant get my head round why the old carbs wouldnt play ball when they come directly off a running bike that run like a dream, i can only think it was down to the 2-3 months of them being in storage and the various rubbers had gone off. Just goes to show you can clean and setup a set of carbs many times and even when everything looks fine doesnt mean it is.

So just need to fix the sticky float on my set of RVF carbs then i shall set them up exaxctly the same as this set :grin:

Thanks to dave, neo and the rest of you that put up with my constant ramblings over these carbs :peace:

Re: RVF Endurance AM-PM Replica build

Posted: Thu Aug 11, 2011 10:36 am
by porndoguk
Drunkn Munky wrote:And one from the other side
Image

I never realised until i look at it now how much that join in the nose cone annoys me, its gota go!
No air tray yet pal but then the postal service round here is crap, next day can sometimes be next week!
Tee,

does our offer still stand on the nose cone ;)

Re: RVF Endurance AM-PM Replica build

Posted: Thu Aug 11, 2011 11:03 am
by Will
i'm so hard right now.

Re: RVF Endurance AM-PM Replica build

Posted: Thu Aug 11, 2011 11:14 am
by Drunkn Munky
Will wrote:i'm so hard right now.
:lol:

Ricky: Yes mate although ive a feeling you will want it before i get round to replacing it, need to save some pennys. Dont forget that you will need RVF headlights and most likey the front stay aswell, and possibly the mid panels.

Re: RVF Endurance AM-PM Replica build

Posted: Thu Aug 11, 2011 11:16 am
by porndoguk
Drunkn Munky wrote:
Will wrote:i'm so hard right now.
:lol:

Ricky: Yes mate although ive a feeling you will want it before i get round to replacing it, need to save some pennys. Dont forget that you will need RVF headlights and most likey the front stay aswell, and possibly the mid panels.
i wont be in a hurry i have a feeling it will be sold me before im ready to have it done anyway,

i shall wait paitently :D