Porndoguk's SEED NC30

[porndoguk]

Porndog, how are you getting on with the bmw shock? I guess today gave you a good chance to test it.?

Depending on how much adjustment you want itll will.need revalveing, ive set mine to all +1 above the middle, but im going to crank it to sport and see how i get on, its very springy. Like a pogo stick, however it still is an improvement and im happy with it.

Cool.

Springy means you gotta stiffen the damping up a bit...right?

Both compression and rebound damping there are three settings options.

Compression damping slow
Compression damping fast
Rebound damping

[lizard821000]

rick is it just me or are you mid panel screws mahoosive??

bike is looking mint pal! deffo one of my fav schemes!

get some sexy dzus fasterners for that mid lad

nomnom

[porndoguk]

rick is it just me or are you mid panel screws mahoosive??

bike is looking mint pal! deffo one of my fav schemes!

get some sexy dzus fasterners for that mid lad

nomnom

im not a fan of the Dzuz fastners tbh, my screws are M6 counter sunk then an alloy fairing washer, i prefer them.

[porndoguk]

[porndoguk]

Current Work and Updates :)

so the story goes, after Bruntingthorpe i decided to strip and rebuild my forks with a polished set of lowers, thanks to lizard. in addition ive always want the SP1 Gold calipers so i did just that, got a tatty pair of eBay For £45, gave them an overhaul and then sold my CBR600 ones straight on to recoup the costs.

also got some stainless 40mm M8s for the calipers aswell as some stainless bleed nipples



also youll notice i have stanchion sheilds from a CBR600F ive had to cut a tiny bit out as the dia is larger, and ive used a large cable tie to clamp them on, seems good to me. form over function







also i removed some fender mounts from a NC23 oem fender, messed around with lemon and baking soda, vinegar and lime juice, and then tried some cheap happy shopper 25p can of rola cola (red bull can size) and it removed about 80% of the rust down to a satin silver finish. drilled the 6mm fender holes to 10mm dia, put them in drilled 3mm holes and riveted them in place like the OEM honda fender no more pissing around to remove it at last.










Also recently removed and sold on my Carbon exhaust hanger as i was never over keen, plus i felt i had a bit to much carbon on the arse end, back to OEM again, with a polished, then brush finish with scotchbrite,

further more 6 spacers i had that kayla sent surplus to requirements, i found good use for 3 of them, one for the exhaust can mount hole, and in addition the 2 mounts on the subframe that took forever to undo due to the thread size after removing the pillion pegs.









also after about 2 months of searching for a 5/8 CBR900 master cylinder steve aka VFRMAN came to my rescue.
it came in a nice clean black and so i put to use a clean CBR600 clutch perch i had so they matched and took my back to stock further more.





Clutch Before

Clutch After





Readjusted my damper




My (Small) Workshop for the curious








Chain measuring Tool!

small screw and precision marked lines on the side of the door :D







Abba Stand customised to work in the tight space,

i need to contact abba this would make there stand 20x better




Exhaust off whilst i sort a problem with the carbon and STILL bunged just in case of the kids!



and rear set risers removed and back to normal tygas

[marcus57]

Looks good Ricky!

[Dynamohum]

That's looking good.. Like the mod to the ABBA stand great stands but need a bit of room simple solution

[Delboy]

Nice to see your bike in print, looking good Rikster

[alexwitham]

Pic whore

[Tim400GB]

Looking good.

Nice exhaust bung