What size flywheel pyller bolt?
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
- Settled in member
- Reactions:
- Posts: 7
- Joined: Sun Jan 29, 2017 9:17 pm
What size flywheel pyller bolt?
What size flywheel pulling bolt do I need to get my flywheel off. I need to replace my generator behind it?
It's a 1990 fzr400rr
Thank you
It's a 1990 fzr400rr
Thank you
-
- Site Supporter
- Reactions:
- Posts: 9490
- Joined: Tue Apr 29, 2008 8:59 pm
- Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
- Location: Lundin Taan
Re: What size flywheel pyller bolt?
you can use the standard bar end weight as a puller.
You'll need to heat the flywheel
You'll need to heat the flywheel
-
- Settled in member
- Reactions:
- Posts: 48
- Joined: Fri Jul 18, 2014 12:31 pm
- Bike owned: FZR 400 RRSP, FZR 400 RR (2)
- Location: Tirol, Austria
Re: What size flywheel pyller bolt?
3TJ /4DX: there is no need to remove the flywheel if you want to exchange the generator.
compressed air screw driver ( no idea what is the correct english name) and a short knock with the hammer and it was done for my flywheel. heating is recommended, but in my experiences, the heat is spreading to fast for the expacted effect.
It is correct standard bar end has the same thread, if I remember correct it's M18 x1,5
BR
compressed air screw driver ( no idea what is the correct english name) and a short knock with the hammer and it was done for my flywheel. heating is recommended, but in my experiences, the heat is spreading to fast for the expacted effect.
It is correct standard bar end has the same thread, if I remember correct it's M18 x1,5
BR
-
- Settled in member
- Reactions:
- Posts: 7
- Joined: Sun Jan 29, 2017 9:17 pm
Re: What size flywheel pyller bolt?
Oh right it's just my generator is behind the magneto so what's best to remove that? Ps don't have a standard bar end unfort. Thank you
-
- Site Supporter
- Reactions:
- Posts: 9490
- Joined: Tue Apr 29, 2008 8:59 pm
- Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
- Location: Lundin Taan
Re: What size flywheel pyller bolt?
Do you have an American model ?
If it's not American then it's a 1wg, there are a few models within the 1wg designation - you have twin headlights, but do you have air intakes ? if so are they above or below the headlights ?
Either way I think the puller thread is the same as the 3TJ described ^^^^ above
If it's not American then it's a 1wg, there are a few models within the 1wg designation - you have twin headlights, but do you have air intakes ? if so are they above or below the headlights ?
Either way I think the puller thread is the same as the 3TJ described ^^^^ above
-
- Settled in member
- Reactions:
- Posts: 7
- Joined: Sun Jan 29, 2017 9:17 pm
Re: What size flywheel pyller bolt?
single headlight bud. G reg. says manufactured 1990 and on v5 was registered 1993.
Also engine mounts are on barrel castings. all evidence leading to a 3tj1 so why isnt my genny bolted to cover instead?
Also engine mounts are on barrel castings. all evidence leading to a 3tj1 so why isnt my genny bolted to cover instead?
-
- Settled in member
- Reactions:
- Posts: 7
- Joined: Sun Jan 29, 2017 9:17 pm
Re: What size flywheel pyller bolt?
says was registered over seas and first uk reg was 1993.
frame says.
3TJ-1117**
if that helps?
frame says.
3TJ-1117**
if that helps?
-
- Settled in member
- Reactions:
- Posts: 48
- Joined: Fri Jul 18, 2014 12:31 pm
- Bike owned: FZR 400 RRSP, FZR 400 RR (2)
- Location: Tirol, Austria
Re: What size flywheel pyller bolt?
to remove it, i have bought a hexagone screw M18x 1.5 len = app 150mm.
now you can use socket wrench and compressed air driver with a lot of torque.
BR
now you can use socket wrench and compressed air driver with a lot of torque.
BR
-
- Site Supporter
- Reactions:
- Posts: 9490
- Joined: Tue Apr 29, 2008 8:59 pm
- Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
- Location: Lundin Taan
Re: What size flywheel pyller bolt?
Odd - Maybe it had a 1WG engine with a 3tj head ???MattyLawsRacing wrote:single headlight bud. G reg. says manufactured 1990 and on v5 was registered 1993.
Also engine mounts are on barrel castings. all evidence leading to a 3tj1 so why isnt my genny bolted to cover instead?
-
- Settled in member
- Reactions:
- Posts: 7
- Joined: Sun Jan 29, 2017 9:17 pm
Re: What size flywheel pyller bolt?
I am also confused. So is it the m16 or m18?
Thank you
Thank you