MY superfour has developed a weird problem since I have got it back on the road and I cant seem to figure it out. It pulls fine from 2500rpm at full throttle but as soon as you hit 7500 it just seems to stop dead. No idea whats going on.
Mods that have been done to it are as follows:
Danmoto Slip on and link pipe
105 Main jets (Too small still maybe?)
K&N Air filter
2.5 Turn Idle mixes
CDI Derestrict Resistor
CR9EH Spark plugs (One range colder)
16/37 Sprockets
Have put new plugs in it today and the problem still persists. It also has new lead ends and the problem only occurs when trying to access the higher part of the rev range at high throttle. Haven't tried lower throttle as If I am up in that part of the rev range then I will more then likely be using over 3/4 throttle anyway.
Any help would be greatly appreciated.
High load miss at >7500rpm
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
- Settled in member
- Posts: 60
- Joined: Tue Oct 30, 2012 10:53 am
- Bike owned: 1994 CB400SF, 2008 CBR600RR
- Location: Australia
- hannakournikova
- Site Supporter
- Posts: 769
- Joined: Wed Apr 30, 2008 6:46 pm
- Bike owned: NC30, NC35 & SP2
- Location: Belfast, Northern Ireland
Re: High load miss at >7500rpm
what have you changed prior too of going back on the road?Gidanski wrote:MY superfour has developed a weird problem since I have got it back on the road and I cant seem to figure it out. It pulls fine from 2500rpm at full throttle but as soon as you hit 7500 it just seems to stop dead. No idea whats going on.
Mods that have been done to it are as follows:
Danmoto Slip on and link pipe
105 Main jets (Too small still maybe?)
K&N Air filter
2.5 Turn Idle mixes
CDI Derestrict Resistor
CR9EH Spark plugs (One range colder)
16/37 Sprockets
Have put new plugs in it today and the problem still persists. It also has new lead ends and the problem only occurs when trying to access the higher part of the rev range at high throttle. Haven't tried lower throttle as If I am up in that part of the rev range then I will more then likely be using over 3/4 throttle anyway.
Any help would be greatly appreciated.
-
- Settled in member
- Posts: 60
- Joined: Tue Oct 30, 2012 10:53 am
- Bike owned: 1994 CB400SF, 2008 CBR600RR
- Location: Australia
Re: High load miss at >7500rpm
The only other thing that has been changed is the instrument cluster. Replaced with an Ebay one as the old one was smashed up. New one did not appear to have a speed sensor or resistor, hence the Derestricter mod.
-
- Settled in member
- Posts: 60
- Joined: Tue Oct 30, 2012 10:53 am
- Bike owned: 1994 CB400SF, 2008 CBR600RR
- Location: Australia
Re: High load miss at >7500rpm
Got it all sorted, turned out to be a bad earth between the battery and chassis.
-
- Settled in member
- Posts: 20
- Joined: Thu Nov 14, 2013 6:27 pm
- Location: Cambridge
Re: High load miss at >7500rpm
Hi
Just thinking out loud here...
Have you checked the rectifier?
Have a look at the coil pickups, there's 3 on the generator casing
Just thinking out loud here...
Have you checked the rectifier?
Have a look at the coil pickups, there's 3 on the generator casing